含间隙弹性传动机构的仿真分析

张涛; 刘宏昭; 冯喜茹; 杨程

doi:10.13433/j.cnki.1003-8728.2015.1004

含间隙弹性传动机构的仿真分析

doi: 10.13433/j.cnki.1003-8728.2015.1004

1.
西安理工大学机械与精密仪器工程学院, 西安 710048

基金项目:

国家自然科学基金项目(51275404)资助

详细信息

作者简介:
张涛(1986-),硕士研究生,研究方向为机电系统性能分析、测试及仿真和机构动力学分析,zhangtao176@163.com

通讯作者:
刘宏昭,教授,博士生导师,liu-hongzhao@163.com

计量
- 文章访问数: 236
- HTML全文浏览量: 35
- PDF下载量: 10
- 被引次数: 0
出版历程
- 收稿日期: 2014-01-13
- 刊出日期: 2015-10-05

Analysis of an Elastic Transmission Mechanism With Joint Clearance

1.
School of Mechanical and Precision Instrument Engineering, Xi'an University of Technology, Xi'an 710048, China

摘要

摘要: 针对间隙及构件弹性对某传动机构的可靠性运行有着较大的影响作用,以该机构的理想状态为基础,建立了同时考虑转动副间隙和构件弹性的机构分析模型。通过ADAMS软件平台仿真,分别对理想机构、含间隙机构、以及同时考虑构件弹性和间隙3种情况下的该传动机构进行模拟,最终得出该传动机构的位移、速度、加速度及运动副接触反力的变化规律。结果表明:间隙副中轴销与轴套产生的内碰撞导致了加速度及副反力较大的波动;而考虑构件弹性后,间隙处产生的加速度及副反力幅值减小,接触碰撞时间增长,即对间隙副中轴销与轴套的碰撞有一定的缓冲作用。
- 转动副间隙 /
- 传动机构 /
- ADAMS /
- 构件弹性
Abstract: Since the joint clearance and linkage elasticity has a comparatively large effect on the reliable operation of a transmission mechanism, considering rotation clearance and the linkage elasticity we established a mechanism analytical model based on the ideal state of the mechanism. The three transmission mechanisms:the ideal mechanism, mechanism with clearance and mechanism with both linkage elasticity and clearance were simulated with ADAMS software. The displacement, velocity, acceleration and the changing rule of the joints contact force for the transmission mechanism were finally obtained. The results show that the in-collisions has led to large fluctuations of the acceleration and contact force, which were produced in the shaft pins and bushings of clearance joints; the acceleration and vice force generated in the clearance were reduced and the contact time was increased while considering the linkage elasticity. This means that the linkage elasticity has a buffering effect on the collision of the shaft pins and bushings in the clearance joints,therefore.
- acceleration /
- ADAMS /
- buffering /
- collision

HTML全文

参考文献(15)

[1]	赵子坤.含间隙机构动力学仿真与实验研究[D]. 大连:大连理工大学,2009 Zhao Z K. Dynamic analysis and experiment research of mechanism with clearance[D]. Dalian:Dalian University of Technology, 2009(in Chinese)
[2]	Dubowsky S, Freudenstein F. Dynamic analysis of mechanical systems with clearances-Part 1:formation of dynamic model[J]. ASME Journal of Engineering for Industry, 1971,93B(1):305-309
[3]	白争锋,赵阳,赵志刚.考虑运动副间隙的机构动态特性研究[J]. 振动与冲击,2011,30(11):17-20 Bai Z F, Zhao Y, Zhao Z G. Dynamic characteristics of mechanisms with joint clearance[J]. Journal of Vibration and Shock, 2011,30(11):17-20(in Chinese)
[4]	鲍和云,朱如鹏,靳广虎,等.间隙对两级星型齿轮传动动态特性的影响研究[J]. 机械科学与技术,2009,28(1):102-107 Bao H Y, Zhu R P, Jin G H, et al. Influence of backlash on the dynamic characteristics of a two-stage star gear train[J]. Mechanical Science and Technology for Aerospace Engineering, 2009,28(1):102-107(in Chinese)
[5]	Flores P, Lankarani H M. Dynamic response of multibody systems with multiple clearance joints[J]. Journal of Computational and Nonlinear Dynamics, 2012,7(3):13-18
[6]	李哲.含间隙弹性平面连杆机构动力分析[J]. 机械工程学报,1994,30(S1):134-139 Li Z. Dynamic analysis of elastic planar linkages with clearances[J]. Chinese Journal of Mechanical Engineering, 1994,30(S1):134-139(in Chinese)
[7]	靳春梅,邱阳,樊灵,等.含间隙弹性机构动态特性分析[J]. 机械强度,2001,23(2):144-147 Jin C M, Qiu Y, Fan L, et al. Dynamic behavior analysis of elastic mechanism with clearances[J]. Journal of Mechanical Strength, 2001,23(2):144-147(in Chinese)
[8]	Dupac M, Beale D B. Dynamic analysis of a flexible linkage mechanism with cracks and clearance[J]. Mechanism and Machine Theory, 2010,12(45):1909-1923
[9]	郭杏林,赵子坤.含间隙柔性曲柄摇杆机构动力学分析[J]. 机械强度,2010,32(6):905-909 Guo X L, Zhao Z K. Dynamic analysis of a flexible crank-rocker mechanism with clearance[J]. Journal of Mechanical Strength, 2010,32(6):905-909(in Chinese)
[10]	Khemili I, Romdhane L. Dynamic analysis of a flexible slider-crank mechanism with clearance[J]. European Journal of Mechanics-A/Solids, 2008,27(5):882-898
[11]	王华杰.基于虚拟样机技术的含间隙转动铰建模方法[J]. 机械研究与应用,2011,6(7):64-67 Wang H J. The modeling method of rotating hinge with clearance based on virtual prototype technology[J]. Mechanical Research and Application, 2011,6(7):64-67(in Chinese)
[12]	赵阳,潘冬,白争锋,等.含间隙卫星天线双轴机构动态磨损特性研究[J]. 机械设计与制造,2011,(5):107-109 Zhao Y, Pan D, Bai Z F, et al. Dynamic wear characteristics analysis for two-axis-position mechanism of satellite antennas with joint clearance[J]. Machinery Design & Manufacture, 2011,(5):107-109(in Chinese)
[13]	阎绍泽,申永胜,陈洪彬.考虑杆件柔性和铰间隙的可展结构动力学数值模拟[J]. 清华大学学报,2003,43(2):145-148 Yan S Z, Shen Y S, Chen H B. Dynamic performance of deployable structures with flexible members and clearance connections[J]. Journal of Tsinghua University, 2003,43(2):145-148(in Chinese)
[14]	刘俊,林砺宗,刘小平,刚.ADAMS柔性体运动仿真分析研究及运用[J]. 现代制造工程,2004,(5):53-55 Liu J, Lin L Z, Liu X P, et al. Study and application of ADAMS flexible body kinetic simulation[J]. Modern Manufacturing Engineering, 2004,(5):53-55(in Chinese)
[15]	郭卫东.虚拟样机技术与ADAMS应用实例教程[M]. 北京:北京航空航天大学出版社,2008 Guo W D. Virtual prototyping technology and ADAMS application examples tutorial[M]. Beijing:Beijing University of Aeronautics and Astronautics Press, 2008(in Chinese)