留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

微小尺寸等壁厚不锈钢螺旋管充液压制成形方法研究

邓娟 王澳 李金平 石昌帅

邓娟,王澳,李金平, 等. 微小尺寸等壁厚不锈钢螺旋管充液压制成形方法研究[J]. 机械科学与技术,2023,42(2):231-240 doi: 10.13433/j.cnki.1003-8728.20200572
引用本文: 邓娟,王澳,李金平, 等. 微小尺寸等壁厚不锈钢螺旋管充液压制成形方法研究[J]. 机械科学与技术,2023,42(2):231-240 doi: 10.13433/j.cnki.1003-8728.20200572
DENG Juan, WANG Ao, LI Jinping, SHI Changshuai. Study on Hydraulic Pressure Forming of Stainless Steel Spiral Pipe with Small Size and Equal Wall Thickness[J]. Mechanical Science and Technology for Aerospace Engineering, 2023, 42(2): 231-240. doi: 10.13433/j.cnki.1003-8728.20200572
Citation: DENG Juan, WANG Ao, LI Jinping, SHI Changshuai. Study on Hydraulic Pressure Forming of Stainless Steel Spiral Pipe with Small Size and Equal Wall Thickness[J]. Mechanical Science and Technology for Aerospace Engineering, 2023, 42(2): 231-240. doi: 10.13433/j.cnki.1003-8728.20200572

微小尺寸等壁厚不锈钢螺旋管充液压制成形方法研究

doi: 10.13433/j.cnki.1003-8728.20200572
基金项目: 国家自然科学基金面上项目(52174210)、四川省自然科学基金项目(23NSFSC2137)、成都市国际科技合作项目(2019-GH02-00034-HZ)及西南石油大学青年科技创新团队项目( 2018CXTD03)
详细信息
    作者简介:

    邓娟(1985−),高级工程师,硕士,研究方向为金属材料应用,blue_dj@126.com

    通讯作者:

    石昌帅,副教授,博士,scs1202@126.com

  • 中图分类号: TE921; TG376.9; TG376.5

Study on Hydraulic Pressure Forming of Stainless Steel Spiral Pipe with Small Size and Equal Wall Thickness

  • 摘要: 为了解决常规螺杆钻具寿命短与微小尺寸螺杆钻具等壁厚定子难加工的问题,本文采用充液压制成形工艺加工微小尺寸等壁厚螺旋管,基于304不锈钢拉伸实验,建立了充液压制成形等壁厚螺旋管有限元模型,用数值模拟方法研究管件外径、壁厚、液压力大小、液压力加载路径、压制速度、摩擦系数对螺旋管质量的影响。结果表明,管件外径为51.8 mm,壁厚为5.3 mm时,螺旋管质量较好,最大液压力为650 MPa,液压力加载路径为路径5,模具挤压速度为0.429 m/s,摩擦因数不超过0.125时,螺旋管加工质量较好,导程误差近似为0,壁厚误差小于8%,平均厚度为5 mm,螺旋管中部壁厚误差小于3%。研究结果可为生产实际中微小尺寸等壁厚不锈钢螺旋管的成形工艺提供参考。
  • 图  1  螺杆钻具定子模型

    图  2  304不锈钢拉伸实验

    图  3  充液压制成形等壁厚螺旋管原理图

    图  4  有限元模型

    图  5  液压力加载路径与模具位移时间路径

    图  6  管件外径对成形质量的影响

    图  7  管件外径变化下的成形极限图

    图  8  管件外径对螺旋管最小壁厚、最大壁厚的影响

    图  9  管件壁厚对成形质量的影响

    图  10  成形极限图

    图  11  管件壁厚对螺旋管壁厚尺寸的影响

    图  12  8种液压力

    图  13  液压力对螺旋管最小、最大壁厚的影响

    图  14  液压力对成形质量的影响

    图  15  液压力变化下的成形极限图

    图  16  8种液压力加载路径

    图  17  液压力加载路径对螺旋管壁厚的影响

    图  18  液压力加载路径对成形质量的影响

    图  19  8种挤压速度

    图  20  挤压速度对螺旋管壁厚的影响

    图  21  挤压速度对成形质量的影响

    图  22  成形极限图

    图  23  挤压速度对壁厚误差的影响

    图  24  摩擦因数对成形质量的影响

    图  25  摩擦因数对壁厚的影响

    表  1  5LZ54定子螺旋管尺寸参数

    外径/mm壁厚/mm导程/mm传动比定子头数
    5453605∶66
    下载: 导出CSV

    表  2  不同壁厚的管件参数

    壁厚/mm5.05.15.25.35.45.5
    中径/mm23.2523.2523.2523.2523.2523.25
    下载: 导出CSV
  • [1] 吕振虎, 王宁, 冯业庆, 等. 高压水力喷射径向钻井技术在彩南油田的应用[J]. 石油规划设计, 2017, 28(1): 18-21

    LV Z H, WANG N, FENG Y Q, et al. Application of radial drilling technology with high-pressure hydraulic jet in Cainan oilfield[J]. Petroleum Planning & Engineering, 2017, 28(1): 18-21 (in Chinese)
    [2] 王志刚, 胡志兴, 李小洋, 等. 水力喷射微小井眼技术用于海域水合物钻探的可行性分析[J]. 探矿工程(岩土钻掘工程), 2020, 47(2): 30-35

    WANG Z G, HU Z X, LI X Y, et al. Feasibility of application of hydraulic jet micro-borehole technology to marine hydrate drilling[J]. Exploration Engineering (Rock & Soil Drilling and Tunneling), 2020, 47(2): 30-35 (in Chinese)
    [3] 魏向辉, 宋苏涵, 张斌, 等. 小井眼PDC钻头 + 螺杆钻具提速技术研究[J]. 设备管理与维修, 2021(S1): 20-22

    WEI X H, SONG S H, ZHANG B, et al. Research on speeding technology of PDC bit and screw drill tool in small hole[J]. Plant Maintenance Engineering, 2021(S1): 20-22 (in Chinese)
    [4] 杨利强, 巴鲁军, 薛江平. 等壁厚螺杆钻具研制与现场试验[J]. 石油钻探技术, 2012, 40(2): 109-112 doi: 10.3969/j.issn.1001-0890.2012.02.021

    YANG L Q, BA L J, XUE J P. Development and field experiment on PDM with uniform wall thickness[J]. Petroleum Drilling Techniques, 2012, 40(2): 109-112 (in Chinese) doi: 10.3969/j.issn.1001-0890.2012.02.021
    [5] 张涛. 等壁厚定子螺杆泵节能效果分析[J]. 石油石化节能, 2017, 7(1): 21-23 doi: 10.3969/j.issn.2095-1493.2017.01.009

    ZHANG T. The energy saving effort of even wall stator PCP[J]. Energy Conservation in Petroleum & Petrochemical Industry, 2017, 7(1): 21-23 (in Chinese) doi: 10.3969/j.issn.2095-1493.2017.01.009
    [6] 习玉阳. 等壁厚螺杆钻具的研制与现场应用[J]. 石油和化工设备, 2018, 21(4): 14-15 + 18 doi: 10.3969/j.issn.1674-8980.2018.04.004

    XI Y Y. Research and field application of uniform wall thickness PDM[J]. Petro & Chemical Equipment, 2018, 21(4): 14-15 + 18 (in Chinese) doi: 10.3969/j.issn.1674-8980.2018.04.004
    [7] 刘璐, 王瑜, 王镇全, 等. 全金属螺杆钻具研究现状与关键技术[J]. 探矿工程(岩土钻掘工程), 2020, 47(4): 24-30

    LIU L, WANG Y, WANG Z Q, et al. Research status and key technology of metal-to-metal screw PDM drills[J]. Exploration Engineering (Rock & Soil Drilling and Tunneling), 2020, 47(4): 24-30 (in Chinese)
    [8] 张端瑞, 文涛, 蒲磊, 等. “垂直钻井工具 + 等壁厚螺杆”提速钻具组合先导性试验——以库车山前高陡构造克深A井为例[J]. 石油钻采工艺, 2020, 42(6): 684-690

    ZHANG D R, WEN T, PU L, et al. Pilot test on the ROP-improvement BHA of vertical drilling tool & screw rod with equal wall thickness: a case study on Well Keshen A in the high-steep structure of Kuqa piedmont area[J]. Oil Drilling & Production Technology, 2020, 42(6): 684-690 (in Chinese)
    [9] 李敏. 等壁厚螺杆钻具定子加工工艺研究[D]. 成都: 西南石油大学, 2006

    LI M. Study on the process technics of uniform wall thick PDM[J]. Chengdu: Southwest Petroleum University, 2006 (in Chinese)
    [10] 邱亚玲, 杨德胜, 韩传军, 等. 等壁厚螺杆钻具定子螺旋槽拉刀设计[J]. 石油矿场机械, 2008, 37(5): 56-58 doi: 10.3969/j.issn.1001-3482.2008.05.013

    QIU Y L, YANG D S, HAN C J, et al. Designs for broach on spiral groove of stator of uniform wall thick PDM[J]. Oil Field Equipment, 2008, 37(5): 56-58 (in Chinese) doi: 10.3969/j.issn.1001-3482.2008.05.013
    [11] 王可, 郭明性, 孙兴伟. 等壁厚螺杆钻具定子管挤压成形的有限元分析[J]. 机械工程与自动化, 2013(3): 17-19 doi: 10.3969/j.issn.1672-6413.2013.03.009

    WANG K, GUO M X, SUN X W. Finite element analysis of rolling forming of uniform wall thickness PDM′s stator pipes[J]. Mechanical Engineering & Automation, 2013(3): 17-19 (in Chinese) doi: 10.3969/j.issn.1672-6413.2013.03.009
    [12] 王新云, 齐紫梅, 金俊松. 等壁厚螺旋管增量成形模设计[J]. 模具工业, 2015, 41(5): 17-21 doi: 10.16787/j.cnki.1001-2168.dmi.2015.05.003

    WANG X Y, QI Z M, JIN J S. Design of die for even-thickness helical tube by incremental forming[J]. Die & Mould Industry, 2015, 41(5): 17-21 (in Chinese) doi: 10.16787/j.cnki.1001-2168.dmi.2015.05.003
    [13] ZHU X H, JI W. Finite element analysis and experimental study on roll-forming method in ISO-wall thickness stator bushing of screw drilling[J]. The International Journal of Advanced Manufacturing Technology, 2017, 93(5-8): 1939-1952 doi: 10.1007/s00170-017-0535-3
    [14] SHI C S, LI J P, DENG J, et al. Study on multi-roller rotary feed forming mechanism of spiral tube with uniform wall thickness[J]. The International Journal of Advanced Manufacturing Technology, 2020, 106(9-10): 4593-4610 doi: 10.1007/s00170-019-04903-8
    [15] ZHU X H, SHI C S, TONG H. Optimizing loading path and die linetype of large length-to-diameter ratio metal stator screw lining hydroforming[J]. Journal of Central South University, 2015, 22(1): 224-231 doi: 10.1007/s11771-015-2513-y
    [16] 石昌帅. 螺杆钻具金属定子衬套线型设计及液压成形方法研究[D]. 成都: 西南石油大学, 2014

    SHI C S. Metal stator lining linetype design of positive displacement motor and tube hydroforming method research[D]. Chengdu: Southwest Petroleum University, 2014 (in Chinese)
    [17] 吕盛强. 螺杆钻具定子衬套液压成形方法研究[D]. 成都: 西南石油大学, 2018

    LYU S Q. Research on hydraulic forming method of stator bushing of sscrew drilling tools[D]. Chengdu: Southwest Petroleum University, 2018 (in Chinese)
    [18] ZHANG S H. Developments in hydroforming[J]. Journal of Materials Processing Technology, 1999, 91(1-3): 236-244 doi: 10.1016/S0924-0136(98)00423-3
    [19] 徐勇, 张士宏, 马彦, 等. 新型液压成形技术的研究进展[J]. 精密成形工程, 2016, 8(5): 7-14 doi: 10.3969/j.issn.1674-6457.2016.05.002

    XU Y, ZHANG S H, MA Y, et al. Hydroforming technology: state-of-the-arts and recent developments[J]. Journal of Netshape Forming Engineering, 2016, 8(5): 7-14 (in Chinese) doi: 10.3969/j.issn.1674-6457.2016.05.002
    [20] 张鑫龙, 贺久强, 韩聪, 等. 椭圆截面管件充液压制变形与应力分析[J]. 机械工程学报, 2017, 53(18): 35-41 doi: 10.3901/JME.2017.17.035

    ZHANG X L, HE J Q, HAN C, et al. Plastic deformation and stress analysis on hydro-pressing of mild steel tube with elliptical section[J]. Journal of Mechanical Engineering, 2017, 53(18): 35-41 (in Chinese) doi: 10.3901/JME.2017.17.035
  • 加载中
图(25) / 表(2)
计量
  • 文章访问数:  129
  • HTML全文浏览量:  95
  • PDF下载量:  12
  • 被引次数: 0
出版历程
  • 收稿日期:  2021-01-26
  • 网络出版日期:  2023-03-27
  • 刊出日期:  2023-02-25

目录

    /

    返回文章
    返回