[1]
|
Ezugwu E O. Key improvements in the machining of difficult-to-cut aerospace superalloys[J]. International Journal of Machine Tools and Manufacture, 2005,45(12-13):1353-1367
|
[2]
|
Jafarian F, Amirabadi H, Fattahi M. Improving surface integrity in finish machining of Inconel 718 alloy using intelligent systems[J]. The International Journal of Advanced Manufacturing Technology, 2014,71(5-8):817-827
|
[3]
|
Meng L H, He N, Yang Y F, et al. Measurement of surface residual stresses generated by turning thin-wall Ti6Al4V tubes using different cutting parameters[J]. Rare Metal Materials and Engineering, 2015,44(10):2381-2386
|
[4]
|
Meng L H, He N, Yang Y F, et al. Method for measuring residual stresses induced by boring in internal surface of tube and its validation with XRD method[J]. Transactions of Nanjing University of Aeronautics and Astronautics, 2014,31(5):508-514
|
[5]
|
Rotella G, Dillon O W, Umbrello D, et al. Finite element modeling of microstructural changes in turning of AA7075-T651 alloy[J]. Journal of Manufacturing Processes, 2013,15(1):87-95
|
[6]
|
Meng L H. Finite element simulation of high speed machining of Ti6Al4V alloy and the corresponding experimental study[C]//Materials Science Forum. Nanjing:Trans Tech Publications, 2016,836-837:444-451
|
[7]
|
Ahmed N, Mitrofanov A V, Babitsky V I, et al. Analysis of material response to ultrasonic vibration loading in turning Inconel 718[J]. Materials Science and Engineering:A, 2006,424(1-2):318-325
|
[8]
|
Courbon C, Kramar D, Krajnik P, et al. Investigation of machining performance in high-pressure jet assisted turning of Inconel 718:an experimental study[J]. International Journal of Machine Tools and Manufacture, 2009,49(14):1114-1125
|
[9]
|
Özel T, Ulutan D. Prediction of machining induced residual stresses in turning of titanium and nickel based alloys with experiments and finite element simulations[J]. CIRP Annals-Manufacturing Technology, 2012,61(1):547-550
|
[10]
|
DeMange J J, Prakash V, Pereira J M. Effects of material microstructure on blunt projectile penetration of a nickel-based super alloy[J]. International Journal of Impact Engineering, 2009,36(8):1027-1043
|
[11]
|
Wang X Y, Huang C Z, Zou B, et al. Dynamic behavior and a modified Johnson-Cook constitutive model of Inconel 718 at high strain rate and elevated temperature[J]. Materials Science and Engineering:A, 2013,580:385-390
|
[12]
|
Klocke F, Lung D, Buchkremer S. Inverse identification of the constitutive equation of Inconel 718 and AISI 1045 from FE machining simulations[J]. Procedia CIRP, 2013,8:212-217
|
[13]
|
Lorentzon J, Järvstra。t N, Josefson B L. Modelling chip formation of alloy 718[J]. Journal of Materials Processing Technology, 2009,209(10):4645-4653
|
[14]
|
Ozel T, Llanos I, Soriano J, et al. 3D finite element modelling of chip formation process for machining Inconel 718:comparison of FE software predictions[J]. Machining Science and Technology, 2011,15(1):21-46
|
[15]
|
Malakizadi A, Cedergren S, Surreddi K B, et al. A methodology to evaluate the machinability of Alloy 718 by means of FE simulation[C]//International Conference on Advanced Manufacturing Engineering and Technologies. Stockholm:NEWTECH, 2013:95-106
|
[16]
|
Del Prete A, Filice L, Umbrello D. Numerical simulation of machining nickel-based alloys[J]. Procedia CIRP, 2013,8:540-545
|
[17]
|
Yanagimoto J, Karhausen K, Brand A J, et al. Incremental formulation for the prediction of flow stress and microstructural change in hot forming[J]. Journal of Manufacturing Science and Engineering, 1998,120(2):316-322
|
[18]
|
Hughes G D, Smith S D, Pande C S, et al. Hall-Petch strengthening for the microhardness of twelve nanometer grain diameter electrodeposited nickel[J]. Scripta Metallurgica, 1986,20(1):93-97
|
[19]
|
Sui F L, Zuo Y, Liu X H, et al. Microstructure analysis on IN 718 alloy round rod by FEM in the hot continuous rolling process[J]. Applied Mathematical Modelling, 2013,37(20-21):8776-8784
|
[20]
|
Umbrello D. Investigation of surface integrity in dry machining of Inconel 718[J]. The International Journal of Advanced Manufacturing Technology, 2013,69(9-12):2183-2190
|