[1]
|
何祝斌,初冠南,张吉,等.锻造技术的发展—从前8届国际塑性加工会议看锻造技术的发展[J].塑性工程学报,2008,15(4):13-18 He Z B, Chu G N, Zhang J, et al. Development of forging technology[J]. Journal of Plasticity Engineering, 2008,15(4):13-18 (in Chinese)
|
[2]
|
黄明辉,李毅波,张猛,等.模锻压机超低速运行动态性能分析[J].中南大学学报(自然科学版),2012,43(11):4259-4267 Huang M H, Li Y B, Zhang M, et al. Dynamic performance analysis for die-forging press machine under extremely low speed[J]. Journal of Central South University (Science and Technology), 2012,43(11):4259-4267 (in Chinese)
|
[3]
|
刘忠伟,刘少军,黄明辉.巨型模锻液压机同步控制系统控制性能影响因素研究[J].锻压技术,2010,35(5):64-68 Liu Z W, Liu S J, Huang M H. Influence factors research on control performance of synchronous control system for giant forging hydraulic press[J]. Forging & Stamping Technology, 2010,35(5):64-68 (in Chinese)
|
[4]
|
刘忠伟,黄明辉,刘新良.巨型模锻液压机同步控制系统的鲁棒控制研究[J].锻压技术,2011,36(5):88-93 Liu Z W, Huang M H, Liu X L. Research on robust control of synchronous control system for giant forging hydraulic press[J]. Forging & Stamping Technology, 2011,36(5):88-93 (in Chinese)
|
[5]
|
熊欢欢.大型模锻液压机动梁驱动及位置控制系统研究[D].长沙:中南大学,2010:27-45 Xiong H H. Research of the large forging hydraulic moving beam and position control system[D]. Changsha: Central South University, 2010:27-45 (in Chinese)
|
[6]
|
朱荣辉.超低速液压机控制系统开发[D].天津:天津大学,2007:6-21 Zhu R H. The development of ultra-low speed hydraulic press control system[D]. Tianjin: Tianjin University, 2007:6-21 (in Chinese)
|
[7]
|
张广红.80MN等温锻造液压机控制系统研制[D].天津:天津大学,2005:8-59 Zhang G H. Research and development of the control system for an 80MN isothermal forging hydraulic press[D]. Tianjin: Tianjin University, 2005:8-59 (in Chinese)
|
[8]
|
刘新良.巨型模锻液压机主动同步控制系统研究[D].长沙:中南大学,2010:31-50 Liu X L. Research of the Giant die forging hydraulic press's active synchronization control system[D]. Changsha: Central South University, 2010:31-50 (in Chinese)
|
[9]
|
段俊.巨型液压机被动同步平衡控制系统的控制策略与实验研究[D].长沙:中南大学,2010:33-49 Duan J. Research of the passive synchronous balance control system's control strategy and its experiment[D]. Changsha: Central South University, 2010:33-49 (in Chinese)
|
[10]
|
李江波.巨型液压机同步平衡系统特性分析及控制策略研究[D].长沙:中南大学,2011:40-51 Li J B. Research of the synchronous balancing system characteristic and its control strategy[D]. Changsha: Central South University, 2011:40-51 (in Chinese)
|
[11]
|
Huang S, Tan K K. Intelligent friction modeling and compensation using neural network approximations[J]. IEEE Transactions on Industrial Electronics, 2012,59(8):3342-3349
|
[12]
|
Lai C Y, Lewis F L, Venkataramanan V, et al. Disturbance and friction compensations in hard disk drives using neural networks[J]. IEEE Transactions on Industrial Electronics, 2010,57(2):784-792
|
[13]
|
林治平.锻压变形力的工程计算[M].北京:机械工业出版社,1986:146-150 Lin Z P. Forging deforming force of engineering calculation[M]. Beijing: China Machine Press, 1986:146-150 (in Chinese)
|
[14]
|
修杰.开关磁阻电机的新型齿极结构及自组织模糊控制[D].天津:天津大学,2004:30-46 Xiu J. Switched reluctance motor's novel tooth pole structure and self-organization fuzzy logical control[D]. Tianjin: Tianjin University, 2004:30-46 (in Chinese)
|