Exploring NC Grinding Residual Stress of Spiral Bevel Gear Using Multi-physical Fields
-
摘要: 根据螺旋锥齿轮的数控磨削机理和Gleason接触原理,得出了影响磨削残余应力的磨削物理参数数学模型。在建立的单齿3D有限元模型基础上,运用热弹塑性理论和数值有限元方法,得到了螺旋锥齿轮磨削温度与应力等物理场;通过这两个物理场的耦合计算,仿真与分析了磨削残余应力。结果表明:螺旋锥齿轮磨削齿面呈现残余压应力,里层为残余拉应力,其大小随磨削工艺条件的不同,呈现一定的变化规律;磨削残余应力随磨削深度和砂轮速度的减小而下降,而随展成速度的减小而增大,干磨比湿磨条件下可明显增加磨削残余应力。实验验证了有限元分析螺旋锥齿轮磨削残余应力的有效性。Abstract: According to the NC grinding mechanism of the spiral bevel gear and the Gleason contact principle,we obtain the mathematical model of grinding physical parameters that influence the grinding residual stress of a spiral bevel gear.We establish the 3D finite element model of the spiral bevel gear;on this basis,we obtain its physical fields such as temperature field and stress field by applying the thermo-elastic-plastic theory and the numerical finite element method.We simulate and analyze the grinding residual stress by doing the coupled computation of the two physical fields.The simulation results show that:(1) the grinding tooth surface of the spiral bevel gear has compressive residual stress;the inside tooth has tensile residual stress;(2) the size of grinding residual stress varies with the varying grinding conditions;the grinding residual stress decreases with decreasing grinding depth and speed of grinding wheel,while increasing with decreasing extended speed;the grinding residual stress is greater in the dry grinding condition than in the wet grinding condition.Finally,the experimental results show that the finite element analysis of grinding residual stresses is effective.
-
Key words:
- NC grinding /
- spiral bevel gear /
- grinding residual stress /
- physical field /
- finite element analysis
-
[1] Bogdan W K,Ryszard W.Residual stress in grinding[J].Jour-nal of Materials Processing Technology,2001,109:254~257 [2] Kuen C E.Finite Element and Analysis of Residual Stresses in 2-D Machining[D].Frankfurt:University of Kentucky,2003 [3] 田欣利等.陶瓷磨削温度对表面残余应力的影响[J].中国机械工程,2002,18(9):1600~1601 [4] 李强,刘志明.高速客车转向架残余应力的试验研究[J].实验力学,1996,(3):57~59 [5] Malkin S,Guo C,张一飞译.外圆磨削加工的仿真、优化及控制[J].金刚石与磨料磨具工程,2001,125(5):11~16 [6] 明兴祖,严宏志,陈书涵等.3D力热耦合磨齿模型研究与数值分析[J].机械工程学报,2008,44(5):17~24 [7] Jin T,Cai G Q.Analytical thermal models of oblique moving heat source for deep grinding and cutting[J].Journal of Manufac-turing Science and Engineering,2001,123(5):185~190 [8] Lin B,Zhang H L.Theoretical analysis of temperature field in sur-face grinding with cup wheel[J].Key Engineering Materials,2001,202~203(6):92~96 -
![WeChat](/fileJXKXYJS/journal/article/jxkxyjs/2012/4/PIC/wechat_cn_5752.jpg)
计量
- 文章访问数: 170
- HTML全文浏览量: 35
- PDF下载量: 5
- 被引次数: 0