Crack Fault Characteristic Analysis of a Wind Turbine Gearbox with Flash Temperature Considered
-
摘要: 为了研究齿面闪温对风电齿轮箱裂纹故障时系统动力学响应的影响,利用Blok闪温理论分析齿轮啮合时的齿面温度,应用热变形公式计算齿廓形变,进而通过Hertz接触理论获得计及齿面闪温影响的轮齿刚度。考虑齿面闪温、阻尼、时变啮合刚度、综合啮合误差和齿侧间隙,建立含有高速级齿轮齿根裂纹的齿轮箱扭转动力学模型。通过时域图、频谱图、相图和Poincaré截面分析不同裂纹长度下系统振动特性随齿面闪温变化的规律,并比较裂纹故障仿真与实验的时频域结果。结果表明:齿面闪温使时域图上裂纹产生的冲击幅值增大、频域图中故障边频结构更为复杂、相图曲线向外扩展以及Poincaré截面离散点增多,且变化均随裂纹长度的增加越为明显。研究结论可为齿轮裂纹故障状态的诊断与监测提供依据。Abstract: In order to study the influence of the flash temperature on the crack fault characteristic of a wind turbine gearbox, the temperature and profile deformation of the tooth are calculated using the Blok flash temperature theory and thermal deformation formula, respectively, and the tooth stiffness considering the flash temperature is obtained using the Hertz contact theory. For the gearbox with crack fault occurred on the tooth root of the high-speed gear, the torsional dynamic model is established considering flash temperature, damping, meshing stiffness, transmission error and backlash. The variation laws of the vibration characteristics with flash temperature are investigated under different crack conditions through time domain, frequency spectrum, phase diagram and Poincaré section, and the numerical results in the time-frequency domain are compared with those of the test without considering the flash temperature. The results show that the flash temperature makes the impact amplitude from the crack in the time domain increase, the fault side frequency be more complex, the phase diagram expand and the number of discrete points in Poincaré section increase, and the changes are more obvious with increasing the crack length. The research provides the basis for diagnosing and monitoring the gear crack fault state.
-
表 1 高速级主动轮裂纹故障参数
Table 1. Parameters of crack faults of the high-speed driving gear
裂纹情况 裂纹长度/mm 裂纹角度/(°) 10%裂纹 q1=0.3 70 20%裂纹 q1=0.6 70 50%裂纹 q1=1.5 70 70%裂纹 q1=1.5, q2=0.6 70 表 2 齿轮箱各齿轮参数
Table 2. Parameters of gears in the gearbox
参数 高速级定轴 中速级定轴 低速级行星传动 1 2 3 4 s p r 齿数 29 100 36 90 28 36 100 模数/mm 1.5 1.5 1.5 1.5 1 1 1 基圆半径/mm 20.4 70.5 25.3 63.4 13 17 47 齿轮质量/g 125 1224.5 224 1111 41 34.6 − 转动惯量/(kg·m2) 0.05 6 0.14 4 0.007 0.01 − 齿宽/mm 30 30 20 20 20 20 20 压力角/(°) 20 20 20 20 20 20 20 热传导系数/[J·(m·s·℃)−1] 46.47 46.47 46.47 46.47 46.47 46.47 46.47 材料密度/(kg·m−3) 7850 7850 7850 7850 7850 7850 7850 弹性模量/GPa 210 210 210 210 210 210 210 比热容/[J·(kg·℃)−1] 481.5 481.5 481.5 481.5 481.5 481.5 481.5 泊松比$ \nu $ 0.3 0.3 0.3 0.3 0.3 0.3 0.3 线膨胀系数/10−5 1.16 1.16 1.16 1.16 1.16 1.16 1.16 齿轮轴半径/mm 5 10 5 15 5 5 5 轴温/℃ 20 20 20 20 20 20 20 基圆面温度/℃ 100 100 100 100 100 100 100 -
[1] 钟龙. 风电机组齿轮箱轮齿裂纹故障建模与仿真研究[D]. 武汉: 华中科技大学, 2015.ZHONG L. Research on modeling and simulation of the gearbox of wind turbine with cracked tooth[D]. Wuhan: Huazhong University of Science and Technology, 2015. (in Chinese) [2] MOHAMMED O D, RANTATALO M. Dynamic response and time-frequency analysis for gear tooth crack detection[J]. Mechanical Systems and Signal Processing, 2016, 66-67: 612-624. doi: 10.1016/j.ymssp.2015.05.015 [3] LIU H, YAN P F, GAO P. Effects of temperature on the time-varying mesh stiffness, vibration response, and support force of a multi-stage planetary gear[J]. Journal of Vibration and Acoustics, 2020, 142(5): 051110. doi: 10.1115/1.4047246 [4] SAXENA A, CHOUKSEY M, PAREY A. Effect of mesh stiffness of healthy and cracked gear tooth on modal and frequency response characteristics of geared rotor system[J]. Mechanism and Machine Theory, 2017, 107: 261-273. doi: 10.1016/j.mechmachtheory.2016.10.006 [5] LIU J, ZHAO W Q, LIU W W. Frequency and vibration characteristics of high-speed gear-rotor-bearing system with tooth root crack considering compound dynamic backlash[J]. Shock and Vibration, 2019, 2019: 1854263. [6] YANG L T, WANG L M, YU W M, et al. Investigation of tooth crack opening state on time varying meshing stiffness and dynamic response of spur gear pair[J]. Engineering Failure Analysis, 2021, 121: 105181. doi: 10.1016/j.engfailanal.2020.105181 [7] WAN Z G, CAO H R, ZI Y Y, et al. An improved time-varying mesh stiffness algorithm and dynamic modeling of gear-rotor system with tooth root crack[J]. Engineering Failure Analysis, 2014, 42: 157-177. doi: 10.1016/j.engfailanal.2014.04.005 [8] WANG L M, SHAO Y M. Fault mode analysis and detection for gear tooth crack during its propagating process based on dynamic simulation method[J]. Engineering Failure Analysis, 2017, 71: 166-178. doi: 10.1016/j.engfailanal.2016.11.003 [9] YANG Y, XIA W K, HAN J M, et al. Vibration analysis for tooth crack detection in a spur gear system with clearance nonlinearity[J]. International Journal of Mechanical Sciences, 2019, 157-158: 648-661. doi: 10.1016/j.ijmecsci.2019.05.012 [10] 肖正明, 郇立荣, 曹金鑫. 裂纹故障对行星齿轮传动系统动力学特性的影响[J]. 振动与冲击, 2020, 39(2): 188-194. doi: 10.13465/j.cnki.jvs.2020.02.026XIAO Z M, XUN L R, CAO J X. Influence of crack fault on the dynamical characteristics of a planetary gear transmission system[J]. Journal of Vibration and Shock, 2020, 39(2): 188-194. (in Chinese) doi: 10.13465/j.cnki.jvs.2020.02.026 [11] 孟宗, 石桂霞, 王福林, 等. 基于时变啮合刚度的裂纹故障齿轮振动特征分析[J]. 机械工程学报, 2020, 56(17): 108-115. doi: 10.3901/JME.2020.17.108MENG Z, SHI G X, WANG F L, et al. Vibration characteristic analysis of cracked gear based on time-varying meshing stiffness[J]. Journal of Mechanical Engineering, 2020, 56(17): 108-115. (in Chinese) doi: 10.3901/JME.2020.17.108 [12] GOU X F, ZHU L Y, QI C Z. Nonlinear dynamic model of a gear-rotor-bearing system considering the flash temperature[J]. Journal of Sound and Vibration, 2017, 410: 187-208. doi: 10.1016/j.jsv.2017.08.014 [13] 张笑, 卢剑伟, 吴祚云, 等. 计入齿面摩擦和热变形的齿轮传动系统动力学建模分析[J]. 振动与冲击, 2017, 36(10): 207-211. doi: 10.13465/j.cnki.jvs.2017.10.033ZHANG X, LU J W, WU Z Y, et al. Dynamic modeling and analysis on gear transmission system with consideration of the tooth surface friction and thermal deformation[J]. Journal of Vibration and Shock, 2017, 36(10): 207-211. (in Chinese) doi: 10.13465/j.cnki.jvs.2017.10.033 [14] 田亚平, 徐璐, 宋佩颉, 等. 含齿面闪温的齿轮副动力学建模与动力特性分析[J]. 机械传动, 2019, 43(6): 48-54. doi: 10.16578/j.issn.1004.2539.2019.06.009TIAN Y P, XU L, SONG P J, et al. Dynamics modeling and dynamic characteristic analysis of a spur gear pair with tooth contact flash temperature[J]. Journal of Mechanical Transmission, 2019, 43(6): 48-54. (in Chinese) doi: 10.16578/j.issn.1004.2539.2019.06.009 [15] PAN W J, LI X P, WANG L L, et al. Nonlinear response analysis of gear-shaft-bearing system considering tooth contact temperature and random excitations[J]. Applied Mathematical Modelling, 2019, 68: 113-136. doi: 10.1016/j.apm.2018.10.022 [16] WANG X. Stability research of multistage gear transmission system with crack fault[J]. Journal of Sound and Vibration, 2018, 434: 63-77. doi: 10.1016/j.jsv.2018.07.037 [17] LIANG X H, ZUO M J, PANDEY M. Analytically evaluating the influence of crack on the mesh stiffness of a planetary gear set[J]. Mechanism and Machine Theory, 2014, 76: 20-38. doi: 10.1016/j.mechmachtheory.2014.02.001 [18] SHI J F, GOU X F, ZHU L Y. Calculation of time-varying backlash for an involute spur gear pair[J]. Mechanism and Machine Theory, 2020, 152: 103956. doi: 10.1016/j.mechmachtheory.2020.103956 [19] SHI Y, YAO Y P, FEI J Y. Analysis of bulk temperature field and flash temperature for locomotive traction gear[J]. Applied Thermal Engineering, 2016, 99: 528-536. doi: 10.1016/j.applthermaleng.2016.01.093 [20] 徐玉秀, 赵晓菲, 熊一奇. 基于传递路径的多级齿轮箱齿轮裂纹故障识别[J]. 仪器仪表学报, 2016, 37(5): 1018-1024. doi: 10.19650/j.cnki.cjsi.2016.05.008XU Y X, ZHAO X F, XIONG Y Q. Gear crack fault identification for multi-stage gearbox based on signal propagation path[J]. Chinese Journal of Scientific Instrument, 2016, 37(5): 1018-1024. (in Chinese) doi: 10.19650/j.cnki.cjsi.2016.05.008