高速冷滚打齿块侧面残余高度解析与试验研究

蒋显伟; 李言; 杨明顺; 姚远; 李渊; 袁启龙

doi:10.13433/j.cnki.1003-8728.2018.0114

高速冷滚打齿块侧面残余高度解析与试验研究

doi: 10.13433/j.cnki.1003-8728.2018.0114

1.
西安理工大学机械与精密仪器工程学院, 西安 710048

基金项目:

国家自然科学基金项目（51475366，51475146）与陕西省科技计划项目（2016JM5074）资助

详细信息

作者简介:
蒋显伟(1985-),助理工程师,硕士,研究方向为先进制造技术,jiangzb151@163.com

计量
- 文章访问数: 183
- HTML全文浏览量: 24
- PDF下载量: 4
- 被引次数: 0
出版历程
- 收稿日期: 2016-07-30
- 刊出日期: 2018-01-15

Experiment and Analysis of Residual Height of Flank Forhigh-speed Cold Rolling Tooth

1.
School of Mechanical and Precision Instrument Engineering, Xi'an University of Technology, Xi'an 710048, China

摘要

摘要: 为提高高速冷滚打成形技术的表面质量，对高速冷滚打齿块侧面残余高度的成因进行理论分析和仿真计算。简述高速冷滚打成形技术的基本原理，分析齿块侧面残余高度的影响因素；对齿块侧面残余高度进行数学几何建模计算，得出残余高度的数学关系式；并通过MATLAB对齿侧面残余高度进行几何仿真，研究分析主要成形参数对其影响。在自主开发的冷滚打设备上进行齿块冷滚打试验，对齿侧面残余高度进行测量，验证了几何解析的正确性和精度可靠性。
- 残余高度 /
- 几何解析 /
- 试验
Abstract: In order to improve the surface quality of high-speed cold rolling lines technology, the cause of residual height of tooth profile of the theoretical analysis and analytic calculation and geometric simulation are studied. The basic principle of high-speed cold rolling technology are briefly discussed, the factors that influence the residual height of the block side teeth are analyzed. The model for residual height is established by calculating the residual height of flank. With MATLAB, the effects of various factors on the residual height geometry are studied. On the self-developed equipment for cold rolling tooth block cold test, the flank residual height were measured so as to verify the correctness of analytic geometry and accuracy reliability.
- residual height /
- geometrical analysis /
- experiment

HTML全文

参考文献(15)

[1]	Silva M B, Skjoedt M, Atkins A G, et al. Single-point incremental forming and formability-failure diagrams[J]. The Journal of Strain Analysis for Engineering Design, 2008,43(1):15-35
[2]	崔凤奎,朱文娟,王晓强,等.高速冷滚打成形技术研究现状与发展趋势[J].河南理工大学学报(自然科学版),2012,31(2):191-195 Cui F K, Zhu W J, Wang X Q, et al. Current research and development trends of high-speed cold rolling technology[J]. Journal of Henan Polytechnic University (Natural Science), 2012,31(2):191-195(in Chinese)
[3]	Cui F K, Wang X Q, Zhang F S, et al. Metal flowing of involute spline cold roll-beating forming[J]. Chinese Journal of Mechanical Engineering, 2013,26(5):1056-1062
[4]	赵晓明.齿条冷滚打变形过程分析[D].西安:西安理工大学,2014 Zhao X M. Analysis of the deformation process of rack cold roll beating[D]. Xi'an:Xi'an University of Technology, 2014(in Chinese)
[5]	李言,杨明顺,李玢,等.丝杠冷滚打成形动力学仿真及分析[J].西安理工大学学报,2009,25(4):383-387 Li Y, Yang M S, Li F, et al. Dynamics simulation and analysis of lead screw cold roll-beating[J]. Journal of Xi'an University of Technology, 2009,25(4):383-387(in Chinese)
[6]	赵智渊,杨明顺,袁启龙,等.基于ABAQUS的丝杠冷滚打变形力仿真[J].铸造技术,2011,32(8):1165-1169 Zhao Z Y, Yang M S, Yuan Q L, et al. Deformation force simulation of lead screw cold roll-beating based on ABAQUS[J]. Foundry Technology, 2011,32(8):1165-1169(in Chinese)
[7]	张璐,李言,杨明顺,等.丝杠冷滚打成形过程金属流动规律研究[J].中国机械工程,2012,23(13):1623-1628 Zhang L, Li Y, Yang M S, et al. Study on metal flowing of lead screw cold roll-beating forming[J]. China Mechanical Engineering, 2012,23(13):1623-1628(in Chinese)
[8]	杨帆,白冰如,龚小涛,等.齿轮高速冷滚打温度及应力分布研究[J].热加工工艺,2013,42(15):105-107 Yang F, Bai B R, Gong X T, et al. Study on temperature and stress distribution of gear in high speed cold rolling[J]. Hot working Technology, 2013,42(15):105-107(in Chinese)
[9]	崔凤奎,徐永福,赵魏.花键冷滚打和铣削加工的金属组织变形研究[J].锻压技术,2008,33(2):70-74 Cui F K, Xu Y F, Zhao W. Research on metal microstructure deformation of splines manufactured by cold rolling, milling and cutting processes[J]. Forging & Stamping Technology, 2008,33(2):70-74(in Chinese)
[10]	崔凤奎,赵魏,徐永福,等.冷滚打成形对花键组织与性能的影响[J].机床与液压,2009,37(12):36-38,100 Cui F K, Zhao W, Xu Y F, et al. Research on fibrous structure and surface work-hardening test of cold rolling involute spline[J]. Machine Tool & Hydraulics, 2009,37(12)36-38,100(inChinese)
[11]	温彤,陈霞.塑性成形过程的缺陷分析模型及其应用[J].锻压装备与制造技术,2006,41(4):12-17 Wen T, Chen X. Theoretic models of defect in metal forming process and their application[J]. China Metalforming Equipment & Manufacturing Technology, 2006,41(4):12-17(in Chinese)
[12]	Csiszár G, Balogh L, Misra A, et al. The dislocation density and twin-boundary frequency determined by x-ray peak profile analysis in cold rolled magnetron-sputter deposited nanotwinned copper[J]. Journal of Applied Physics, 2011,110(4):043502
[13]	朱艳春,曾卫东,冯菲,等.数值模拟技术及其在塑性成形缺陷预测中的应用[J].材料导报,2010,24(23):104-108 Zhu Y C, Zeng W D, Feng F, et al. Technology of numerical simulation and its application in defect prediction of plastic forming process[J]. Materials Review, 2010,24(23):104-108(in Chinese)
[14]	吕日松,董万鹏,陈军.金属塑性成形缺陷的数值模拟预测研究[J].模具技术,2003,(3):3-4,18 Lv R S, Dong W P, Chen J. Research on defect prediction of metal forming process by finite element simulation[J]. Die and Mould Technology, 2003,(3):3-4,18(in Chinese)
[15]	杨明顺,李言,袁启龙,等.板料冷滚打成形鳞纹影响因素解析及试验研究[J],机械科学与技术,2013,32(9):1363-1367 Yang M S, Li Y, Yuan Q L, et al. Theoretical analysis and experimental study on stripe of slab cold roll-beating[J]. Mechanical Science and Technology for Aerospace Engineering, 2013,32(9):1363-1367(in Chinese)