Research on Joint Control of Combined Drivers with Synchronization for Giant Forging Hydraulic Press
-
摘要: 高性能复杂整体模锻件要求模锻液压机必须具备多缸同步以及稳定运行的能力,但巨大运动惯量、复杂多变的负载以及锻件材质不均、形状不对称导致该装备运行时极易出现速度不稳定和活动横梁倾斜现象。针对这一问题,在考虑液压机液压非线性与复杂多变负载的基础上,建立了模锻液压机整体运动模型,并提出了驱动与同步过程联合控制的方法。通过对驱动过程采用多因子自调整模糊控制,对同步过程采用模糊解耦控制,使系统不仅实现了锻压速度的平稳控制,同时也保证了系统的同步性能。最后通过仿真和实验验证了该控制的有效性,为控制大惯量模锻液压机平稳运行提供了理论基础与保证。Abstract: High-performanced and complex integral die forgings require the forging hydraulic press has the function of synchronous operation with multi-cylinder and stable operation. However, with the reason of the huge moving inertia, complex and variable load, non-uniform forging material and asymmetric in shape, the equipment extremely tends to be unstable in speed and its moving beam is also easy to tilt. In view of these problems, considering the hydraulic nonlinear and complex load, we establish a motion model for forging press. Meanwhile, a method of joint control of combined drivers with synchronization was proposed. With a multi-factor self-tuning fuzzy control to drive subsystem and a fuzzy decoupling control to the synchronization subsystem, the press can not only achieve a forging stable speed, but also has high-precision synchronization performance. At last, the system effectiveness has been verified via the simulation and experiment results. All these will provide with theoretical foundations and guarantees for the large inertia equipment's precise operation.
-
Key words:
- drive system /
- forging hydraulic press /
- stable operation /
- synchronization system
-
[1] 何祝斌,初冠南,张吉,等.锻造技术的发展—从前8届国际塑性加工会议看锻造技术的发展[J].塑性工程学报,2008,15(4):13-18 He Z B, Chu G N, Zhang J, et al. Development of forging technology[J]. Journal of Plasticity Engineering, 2008,15(4):13-18 (in Chinese) [2] 黄明辉,李毅波,张猛,等.模锻压机超低速运行动态性能分析[J].中南大学学报(自然科学版),2012,43(11):4259-4267 Huang M H, Li Y B, Zhang M, et al. Dynamic performance analysis for die-forging press machine under extremely low speed[J]. Journal of Central South University (Science and Technology), 2012,43(11):4259-4267 (in Chinese) [3] 刘忠伟,刘少军,黄明辉.巨型模锻液压机同步控制系统控制性能影响因素研究[J].锻压技术,2010,35(5):64-68 Liu Z W, Liu S J, Huang M H. Influence factors research on control performance of synchronous control system for giant forging hydraulic press[J]. Forging & Stamping Technology, 2010,35(5):64-68 (in Chinese) [4] 刘忠伟,黄明辉,刘新良.巨型模锻液压机同步控制系统的鲁棒控制研究[J].锻压技术,2011,36(5):88-93 Liu Z W, Huang M H, Liu X L. Research on robust control of synchronous control system for giant forging hydraulic press[J]. Forging & Stamping Technology, 2011,36(5):88-93 (in Chinese) [5] 熊欢欢.大型模锻液压机动梁驱动及位置控制系统研究[D].长沙:中南大学,2010:27-45 Xiong H H. Research of the large forging hydraulic moving beam and position control system[D]. Changsha: Central South University, 2010:27-45 (in Chinese) [6] 朱荣辉.超低速液压机控制系统开发[D].天津:天津大学,2007:6-21 Zhu R H. The development of ultra-low speed hydraulic press control system[D]. Tianjin: Tianjin University, 2007:6-21 (in Chinese) [7] 张广红.80MN等温锻造液压机控制系统研制[D].天津:天津大学,2005:8-59 Zhang G H. Research and development of the control system for an 80MN isothermal forging hydraulic press[D]. Tianjin: Tianjin University, 2005:8-59 (in Chinese) [8] 刘新良.巨型模锻液压机主动同步控制系统研究[D].长沙:中南大学,2010:31-50 Liu X L. Research of the Giant die forging hydraulic press's active synchronization control system[D]. Changsha: Central South University, 2010:31-50 (in Chinese) [9] 段俊.巨型液压机被动同步平衡控制系统的控制策略与实验研究[D].长沙:中南大学,2010:33-49 Duan J. Research of the passive synchronous balance control system's control strategy and its experiment[D]. Changsha: Central South University, 2010:33-49 (in Chinese) [10] 李江波.巨型液压机同步平衡系统特性分析及控制策略研究[D].长沙:中南大学,2011:40-51 Li J B. Research of the synchronous balancing system characteristic and its control strategy[D]. Changsha: Central South University, 2011:40-51 (in Chinese) [11] Huang S, Tan K K. Intelligent friction modeling and compensation using neural network approximations[J]. IEEE Transactions on Industrial Electronics, 2012,59(8):3342-3349 [12] Lai C Y, Lewis F L, Venkataramanan V, et al. Disturbance and friction compensations in hard disk drives using neural networks[J]. IEEE Transactions on Industrial Electronics, 2010,57(2):784-792 [13] 林治平.锻压变形力的工程计算[M].北京:机械工业出版社,1986:146-150 Lin Z P. Forging deforming force of engineering calculation[M]. Beijing: China Machine Press, 1986:146-150 (in Chinese) [14] 修杰.开关磁阻电机的新型齿极结构及自组织模糊控制[D].天津:天津大学,2004:30-46 Xiu J. Switched reluctance motor's novel tooth pole structure and self-organization fuzzy logical control[D]. Tianjin: Tianjin University, 2004:30-46 (in Chinese)
点击查看大图
计量
- 文章访问数: 213
- HTML全文浏览量: 35
- PDF下载量: 10
- 被引次数: 0