弧线齿面齿轮的几何设计和数控加工

蔡香伟; 方宗德; 苏进展

弧线齿面齿轮的几何设计和数控加工

1.
西北工业大学机电学院,西安 710072

基金项目:

国家自然科学基金项目(50875211)资助

详细信息

作者简介:
蔡香伟(1987-)，博士研究生，研究方向为齿轮的设计制造，caixiangwei@163.com;方宗德(联系人)，教授，博士生导师，fanto@nwpu.edu.cn

蔡香伟(1987-)，博士研究生，研究方向为齿轮的设计制造，caixiangwei@163.com;方宗德(联系人)，教授，博士生导师，fanto@nwpu.edu.cn

计量
- 文章访问数: 173
- HTML全文浏览量: 25
- PDF下载量: 17
- 被引次数: 0
出版历程
- 收稿日期: 2011-12-13
- 刊出日期: 2015-06-10

Geometrical Design and Manufacture on NC Machine for Face Gear with Arcuate Tooth

1.
School of Mechanical and Electronical Engineering,Northwestern Polytechnical University,Xi'an 710072

摘要

摘要: 研究了弧线齿面齿轮的齿面展成原理,给出了内半径、外半径的求解方法,以及弧线齿面齿轮在普通多轴联动数控机床上的加工实现。基于假想齿轮的概念,推导弧线齿面齿轮的齿面方程;依据面齿轮内径处根切,外径处齿顶变尖条件,确定弧线齿面齿轮的齿宽界限值;以坐标变换为工具,建立了弧线齿面齿轮在数控机床上的加工方法,确定了各运动轴的多项式表达式,以方便数控编程。通过算例,分析产形齿轮齿数、刀盘半径、刀倾角等加工参数对弧线齿面齿轮齿宽的影响;根据运动轴多项式,建立面齿轮的三维实体模型,验证在数控机床加工的可行性。
- 弧线齿面齿轮 /
- 假想齿轮 /
- 面齿轮根切 /
- 面齿轮变尖 /
- 运动转换
Abstract: The generating of face gear with arcuate tooth was studied in this paper.The value of inner radius and outer radius of face gear,and its manufacture on NC machine were investigated.Tooth surface equation was derived based on the concept of imaginary gear.According to the conditions of undercutting in the dedendum area of inner radius and the pointing of the tooth in the addendum area in outer radius,tooth width limiting value was determined.The machining principle in the general multi-axle numerical control machine tool was created by using coordinate transformation.Then the polynomial expression of motion axes was obtained.An example was employed to analyze the tooth width with different design parameters such as the number of imaginary tooth,cutter head radius,initial tilted angle,etc.Tooth surface model was established,and the result proves the manufacture is feasible.
- face gear with arcuate gear /
- dedendum undercutting /
- kinematics transformation /
- NC machining /
- gear design

HTML全文

参考文献(12)

[1]	Litvin F L,Fuentes A. Gear Geometry and Applied Theory[M].Cambridge:Cambridge University Press,2004.
[2]	Litvin F L,Fuentes A,Zanzi C. Design,generation,and stress analysis of two versions of geometry of face-gear drives[J].Mechanism and Machine Theory,2002,(10):1179-1211.
[3]	Litvin F L,Gonzalez-Perez I,Fuentes A. Design,genera-tion and stress analysis of face-gear drive with helical pinion[J].Computer Methods in Applied Mechanics and Engineering,2005,(36-38):3870-3901.
[4]	Chang S H,Chung T D,Lu S S. Tooth contact analysis of face-gear drives[J].International Journal of Mechanical Sci-ences,2000,(03):487-502.
[5]	朱如鹏,高德平. 在面齿轮设计中避免根切和齿顶变尖的设计方法的研究[J].中国机械工程,1999,(11):1274-1276.
[6]	沈云波,方宗德,赵宁. 斜齿面齿轮齿宽的设计[J].航空动力学报,2008,(04):754-758.
[7]	赵宁,曾晓春,郭辉. 斜齿面齿轮齿面仿真及其轮齿接触分析[J].航空动力学报,2008,(10):1927-1932.
[8]	方宗德,沈云波. 弧线齿面齿轮副及其加工方法[P].中国,200710017256,2010.
[9]	方宗德,曹雪梅,沈云波. 弧线齿面齿轮的齿面设计与加工[J].航空动力学报,2010,(01):224-227.
[10]	苏进展,方宗德,曹雪梅. 成形法加工的弧线齿面齿轮几何接触分析[J].航空动力学报,2010,(06):1427-1431.
[11]	苏进展,方宗德,曹雪梅. 刀倾法数控加工机床调整参数转换[J].农业机械学报,2009,(11):223-226.
[12]	王小椿,吴联银,李彬. 基于空间运动学的传统机床与Free-Form型机床运动转换方法的研究[J].机械工程学报,2001,(04):93-98.