|
|
论文:2023,Vol:41,Issue(4):670-678 |
|
|
引用本文： |
|
|
付晓军, 李欣, 马尚君, 佟瑞庭, 刘更. 环形牙滚柱丝杠啮合机理研究[J]. 西北工业大学学报 |
|
|
FU Xiaojun, LI Xin, MA Shangjun, TONG Ruiting, LIU Geng. Study on the meshing theory of the ring-shaped roller screw mechanism[J]. Journal of Northwestern Polytechnical University |
|
|
|
|
|
|
|
| 环形牙滚柱丝杠啮合机理研究 |
|
| 付晓军, 李欣, 马尚君, 佟瑞庭, 刘更 |
|
| 西北工业大学 陕西省机电传动与控制工程实验室, 陕西 西安 710072 |
| 摘要: |
| 基于环形牙滚柱丝杠结构特点,推导了丝杠、滚柱和螺母的曲面方程,建立了计算丝杠和滚柱以及螺母和滚柱之间接触位置的啮合方程,给出了环形牙滚柱丝杠的轴向间隙计算公式和零间隙牙厚设计量。通过与现有数值模型接触位置和间隙计算结果的对比,验证了所建模型的正确性,分析了结构参数对环形牙滚柱丝杠啮合特性的影响规律。分析结果表明:较大的丝杠名义半径和较小的滚柱名义半径有利于接触点接近两零件中径切点位置;丝杠和滚柱的接触位置对两零件的牙侧角差值十分敏感;当螺母和滚柱牙侧角相同时,接触点位于两者的中径切点且零间隙牙厚设计量等于螺距的一半;滚柱牙型轮廓半径对丝杠和滚柱的零间隙牙厚设计量几乎无影响。 |
| 关键词:
滚柱丝杠
环形牙
螺旋曲面
接触位置
间隙
|
|
| Study on the meshing theory of the ring-shaped roller screw mechanism |
|
| FU Xiaojun, LI Xin, MA Shangjun, TONG Ruiting, LIU Geng |
|
| Shaanxi Engineering Laboratory for Transmissions and Controls, Northwestern Polytechnical University, Xi'an 710072, China |
| Abstract: |
| Based on the structural characteristics of ring-shaped roller screw mechanism (RRSM), helical equations of the screw, roller and nut are derived. Meshing equations at the screw-roller and nut-roller interfaces are developed, which can be used to calculated contact positions of thread teeth. The equations of axial clearances in the RRSM are also derived and zero-clearance design values of the thread thicknesses are given. By comparing the contact positions and clearances obtained from a previously published numerical model, the feasibility of the proposed model is validated. The influence of structural parameters on the meshing characteristics of the RRSM is analyzed. When the nominal radius of the screw is increased or that of the roller is decreased, the contact point at the screw-roller interface will move towards to the tangential-point of pitch circles. The difference between the value of the screw flank angle and that of the screw flank angle has great influence on contact positions. When the values of the nut and roller flank angles are equal, the contact points will lie on the tangential-point of pitch circles and the zero-clearance design value of the thread thickness at the nut-roller interface is equal to the half of the screw pitch. The radius of the roller thread profile has little influence on the zero-clearance design values of thread thickness. |
| Key words:
roller screw mechanism
ring-shaped tooth
helical surface
contact position
clearance
|
|
| 收稿日期: 2022-09-01
修回日期:
|
| DOI: 10.1051/jnwpu/20234140670 |
| 基金项目: 国家自然科学基金(51905428,51875458)、中央高校基本科研业务费(31020220502009)及国家重点研发计划(2019YFB2004700)资助 |
| 通讯作者:
Email： |
| 作者简介: 付晓军(1987—),西北工业大学副教授,主要从事行星滚柱丝杠传动和机电作动系统研究。e-mail:fuxiaojun@nwpu.edu.cn
|
|
| 相关功能 |
|
|
|
|
| 作者相关文章 |
|
| 付晓军 在本刊中的所有文章 |
| 李欣 在本刊中的所有文章 |
| 马尚君 在本刊中的所有文章 |
| 佟瑞庭 在本刊中的所有文章 |
| 刘更 在本刊中的所有文章 |
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] FU X J, LI X, MA S J, et al. A multi-roller static model of the planetary roller screw mechanism considering load sharing[J]. Tribology International, 2022, 173(2022): 107648-1-15
[2] DU X, Chen B K, ZHENG Z D. Investigation on mechanical behavior of planetary roller screw mechanism with the effects of external loads and machining errors[J]. Tribology International, 2021, 154(2021): 106689-1-12
[3] FU X J, LIU G, MA S J, at al. Kinematics model of planetary roller screw mechanism with run-out and position errors[J], ASME Journal of Mechanical Design, 2018, 140(1): 032301-1-10
[4] JONES M H, VELINSKY S A. Kinematics of roller migration in the planetary roller screw mechanism[J]. ASME Journal of Mechanical Design, 2012, 134(6): 061006-1-6
[5] JONES M H, VELINSKY S A, LASKY T A. Dynamics of the planetary roller screw mechanism[J]. ASME Journal of Mechanisms and Robotics, 2016, 8(1): 014503-1-6
[6] FU X J, LIU G, LI X, et al. Dynamic modeling of the double-nut planetary roller screw mechanism considering elastic deformations[J]. ASME Journal of Computational and Nonlinear Dynamics, 2021, 16(2021): 051003-1-13
[7] ZHOU G W, ZHANG Y H, WANG Z Z, et al. Analysis of transient mixed elastohydrodynamic lubrication in planetary roller screw mechanism[J]. Tribology International, 2021, 163(2021): 107158-1-12
[8] BLINOV D S, RYAKHOVSKY O A, SOKOLOV P A. Numerical method of determining the point of initial thread contact of two screws with parallel axes and different thread inclinations[J]. Scientific Journal of Murmansk State Technical University, 1996(3): 93-97
[9] JONES M H, VELINSKY S A. Contact kinematics in the roller screw mechanism[J]. ASME Journal of Mechanical Design, 2013, 135(5): 051003-1-10
[10] LIU Y Q, WANG J S, CHENG H G, et al. Kinematics analysis of the roller screw based on the accuracy of meshing point calculation[J/OL].(2015-05-09)[2023-07-14]. https://www.hindawi.com/journals/mpe/2015/303972/
[11] LIU Y Q, SHANG Y, WANG J S. Mathematical analysis of the meshing performance of planetary roller screws applying different roller thread shapes[J]. Advances in Mechanical Engineering, 2017, 9(5): 1-11
[12] 徐强, 王水铭, 赵国平, 等. PWG型差动丝杠的啮合干涉分析与消除[J]. 组合机床与自动化加工技术, 2015, (9): 107-109 XU Qiang. WANG Shuiming, ZHAO Guoping, et al. The analysis of meshing interference and elimination of PWG planetary roller screw[J]. Modular Machine Tool & Automatic Manufacturing Technique, 2015, (9): 107-109 (in Chinese)
[13] FU X J, LIU G, MA S J, et al. A comprehensive contact analysis of planetary roller screw mechanism[J]. ASME Journal of Mechanical Design, 2017, 139(1): 012302-1-11
[14] 刘佳, 彭航, 罗英, 等. 行星滚柱丝杠传动副接触外形函数及接触模型研究[J]. 核动力工程, 2021, 42(2): 180-182 LIU Jia, PENG Hang, LUO Ying, et al. Research on contact shape function and contact model of planetary roller screw drive pair[J]. Nuclear Power Engineering, 2021, 42(2): 180-182 (in Chinese)
[15] XING M C, ZHANG B H, DENG P, et al. A novel wear prediction model for planetary roller screw based on universal sliding distance model[J]. Tribology International, 2022, 175(2022): 107851-1-11 |
|
|
|
相关文献: |
|
|
1．李强, 张佼龙, 周军, 高智刚.行星滚柱丝杠传动机构非线性建模与仿真[J]. 西北工业大学学报, 2015,33(5): 739-743 |
|
|
|
|
|
|
