|
|
论文:2023,Vol:41,Issue(3):471-479 |
|
|
引用本文： |
|
|
黄艳, 任飞翔, 陈普会. 基于试验及数值仿真的复合材料单钉双剪连接件失效研究[J]. 西北工业大学学报 |
|
|
HUANG Yan, REN Feixiang, CHEN Puhui. Study on failure of single-bolt double-lap composite joints based on test and numerical emulation[J]. Journal of Northwestern Polytechnical University |
|
|
|
|
|
|
|
| 基于试验及数值仿真的复合材料单钉双剪连接件失效研究 |
|
| 黄艳1, 任飞翔2, 陈普会1 |
|
1. 南京航空航天大学 机械结构力学及控制国家重点实验室, 江苏 南京 210016;
2. 中国航空工业集团有限公司 成都飞机设计研究所, 四川 成都 610091 |
| 摘要: |
| 为研究ZT7G/LT-03A碳纤维环氧树脂复合材料单钉双剪连接件的力学性能，对3种铺层与3种宽度的层合板开展了复合材料单钉双剪试验，分析了不同铺层比例、宽径比对失效载荷与失效模式的影响。采用渐进损伤失效分析方法对试件的失效过程进行了有限元模拟，模型与试件的失效模式以及失效载荷吻合良好，验证了模型的准确性。在此基础上，研究了初次掉载时层合板各个铺层的应力分布与损伤状况，并进一步探究了整个加载历程中不同铺层比例与宽径比对连接件性能的影响。结果表明，当层合板的宽径比增加时，失效模式由拉伸失效转变为挤压失效，而在一定范围内改变铺层比例时，失效模式基本不受影响。 |
| 关键词:
复合材料
挤压强度
单钉双剪连接
铺层比例
宽径比
|
|
| Study on failure of single-bolt double-lap composite joints based on test and numerical emulation |
|
| HUANG Yan1, REN Feixiang2, CHEN Puhui1 |
|
1. State Key Laboratory of Mechanics and Control of Mechanical Structures, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;
2. Chengdu Aircraft Design and Research Institute, Aviation Industry Corporation of China, Ltd., Chengdu 610091, China |
| Abstract: |
| In order to study the mechanical properties of ZT7G/LT-03A carbon fiber reinforced composite bolted joints, the single-bolt double-lap joints tests were carried out with 3 kinds of ply and 3 kinds of width, and the effects of the different ply ratios, width to diameter ratios on the failure load and failure mode were analyzed. Then, the failure process of the specimens was simulated by using the progressive damage and failure analysis method. The failure mode and failure load of the model are consistent with that of the specimen, which verified the accuracy of the model. On this basis, the stress and damage status of each ply during initial load shedding were studied, and the influence of the ply ratios and width to diameter ratios on the performance of laminates was further studied. The results show that when the width to diameter ratio of laminates increases, the failure mode changes from tensile failure to bearing failure, and to change the ply ratios does not affect the failure mode in a certain range. |
| Key words:
composite
bearing strength
single-bolted double-lapped joints
ply ratio
width to diameter ratio
|
|
| 收稿日期: 2022-08-25
修回日期:
|
| DOI: 10.1051/jnwpu/20234130471 |
| 通讯作者: 陈普会(1964—),南京航空航天大学教授,主要从事复合材料结构设计技术研究。e-mail:phchen@nuaa.edu.cn
Email：phchen@nuaa.edu.cn |
| 作者简介: 黄艳(1997—),南京航空航天大学博士研究生,主要从事复合材料结构设计技术研究。
|
|
| 相关功能 |
|
|
|
|
| 作者相关文章 |
|
| 黄艳 在本刊中的所有文章 |
| 任飞翔 在本刊中的所有文章 |
| 陈普会 在本刊中的所有文章 |
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] 何柏灵, 葛东云, 莫与明, 等. T800碳纤维增强复合材料双剪单钉连接的拉伸试验及强度估算[J]. 复合材料学报, 2016, 33(7):1540-1552 HE Boling, GE Dongyun, MO Yuming, et al. Tensile tests and strength estimation for double-lap single-bolt joints in T800 carbon fiber reinforced composites[J]. Acta Materiae Compositae Sinica, 2016, 33(7):1540-1552(in Chinese)
[2] 赵丽滨, 徐吉峰. 先进复合材料连接结构分析方法[M]. 北京:北京航空航天大学出版社, 2015:75-76 ZHAO Libin, XU Jifeng. Analysis method of connection structure of advanced composite materials[M]. Beijing:Beihang University Press, 2015:75-76(in Chinese)
[3] AKTAS A, DIRIKOLU M H. The effect of stacking sequence of carbon epoxy composite laminates on pinned-joint strength[J]. Composite Structures, 2003, 62(1):107-111
[4] CAO Y, ZUO D, ZHAO Y, et al. Experimental investigation on bearing behavior and failure mechanism of double-lap thin-ply composite bolted joints[J]. Composite Structures, 2021, 261:113565
[5] 曹跃杰, 魏凌峰, 张铭豪, 等. 薄层复合材料螺栓连接结构渐进失效机制试验研究[J]. 航空学报, 2021, 42(12):311-326 CAO Yuejie, WEI Lingfeng, ZHANG Minghao, et al. Experimental study on progressive failure mechanism of thin-laminate bolted joints[J]. Acta Aeronautica et Astronautica Sinica, 2021, 42(12):311-326(in Chinese)
[6] ALUKO O, WHITWORTH H A. Analysis of stress distribution around pin loaded holes in orthotropic plates[J]. Composite Structures, 2008, 86(4):308-313
[7] 杨显昆, 郑锡涛, 成李南, 等. 复合材料层合板单钉双剪连接挤压强度的一种工程估算方法[J]. 复合材料学报, 2012, 29(6):225-229 YANG Xiankun, ZHENG Xitao, CHENG Linan, et al. An engineering approach to predict the bearing strength of single-bolted double-lapped joints in composite laminate[J]. Acta Materiae Compositae Sinica, 2012, 29(6):225-229(in Chinese)
[8] 黄河源, 赵美英, 万小朋, 等. 一种复合材料螺栓连接结构非线性刚度模型及应用[J]. 西北工业大学学报, 2018, 36(1):66-73 HUANG Heyuan, ZHAO Meiying, WAN Xiaopeng, et al. A composite bolted joints non-linear stiffness model and its application[J]. Journal of Northwestern Polytechnical University, 2018, 36(1):66-73(in Chinese)
[9] IÇTEN B M, KARAKUZU R. Progressive failure analysis of pin-loaded carbon-epoxy woven composite plates[J]. Composites Science and Technology, 2002, 62(9):1259-1271
[10] IÇTEN B M, KARAKUZU R, TOYGAR M E. Failure analysis of woven kevlar fiber reinforced epoxy composites pinned joints[J]. Composite Structures, 2006, 73(4):443-450
[11] JOSEPH A P, DAVIDSON P, WAAS A M. Progressive damage and failure analysis of single lap shear and double lap shear bolted joints[J]. Composites Part A:Applied Science and Manufacturing, 2018, 113:264-274
[12] 陈鹏飞, 赵美英, 穆朋刚, 等. 一种工程适用的复合材料螺栓连接强度分析方法[J]. 西北工业大学学报, 2008, 26(2):229-233 CHEN Pengfei, ZHAO Meiying, MU Penggang, et al. Improving method for analyzing strength of composite material bolted joint[J]. Journal of Northwestern Polytechnical University, 2008, 26(2):229-233(in Chinese)
[13] 刘向东, 李亚智, 李彪,等. 复合材料机械连接数值模型和强度研究[J]. 西北工业大学学报, 2013, 31(6):878-883 LIU Xiangdong, LI Yazhi, LI Biao, et al. On numerical modeling and tensile strength of bolted composite joints[J]. Journal of Northwestern Polytechnical University, 2013, 31(6):878-883(in Chinese)
[14] DU A, LIU Y, XIN H, et al. Progressive damage analysis of PFRP double-lap bolted joints using explicit finite element method[J]. Composite Structures, 2016, 152:860-869
[15] SHAN M, LIU F, FANG Z, et al. A bi-material property based FE modelling method for progressive damage analyses of composite double-lap bolted joints[J]. Results in Physics, 2018, 11:674-683
[16] ABD-ELHADY A A, MUBARAKI M A, SALLAM H E M. Progressive failure prediction of pinned joint in quasi-isotropic laminates used in pipelines[J]. Latin American Journal of Solids and Structures, 2018, 15(6):96
[17] ZHOU S, YANG C, TIAN K, et al. Progressive failure modelling of double-lap of composite bolted joints based on Puck's criterion[J]. Engineering Fracture Mechanics, 2018, 206:233-249
[18] FIORE V, CALABRESE L, SCALICI T, et al. Bearing strength and failure behavior of pinned hybrid glass-flax composite laminates[J]. Polymer Testing, 2018, 69:310-319
[19] 拓宏亮, 马晓平, 卢智先. 基于连续介质损伤模型的复合材料连接件失效分析[J]. 西北工业大学学报, 2018, 36(5):848-855 TUO Hongliang, MA Xiaoping, LU Zhixian. Failure analysis of composite pinned joints based on continuum damage mechanics[J]. Journal of Northwestern Polytechnical University, 2018, 36(5):848-855(in Chinese)
[20] 唐玉玲, 陈浩, 周振功, 等. C/C编织复合材料双剪连接结构的挤压强度[J]. 机械工程学报, 2020, 56(18):51-60 TANG Yuling, CHEN Hao, ZHOU Zhengong, et al. Bearing strength of carbon/carbon braided composites double shear joint[J]. Journal of Mechanical Engineering, 2020, 56(18):51-60(in Chinese)
[21] 钟茂平, 毛春见, 张霞. 配合精度对复合材料单钉双剪螺栓连接静强度的影响[J]. 材料科学与工程学报, 2021, 39(5):750-756 ZHONG Maoping, MAO Chunjian, ZHANG Xia. Effect of clearance and interference on static strength of single-bolt, double-lap composite bolted joints[J]. Journal of Materials Science & Engineering, 2021, 39(5):750-756(in Chinese)
[22] 顾杰斐. 飞机结构材料的失效准则研究[D]. 南京:南京航空航天大学, 2018 GU Jiefei. Research on failure criteria for aircraft structural materials[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2018(in Chinese)
[23] American Society for Testing and Materials. Standard test method for bearing response of polymer matrix composite laminates[S]. ASTM D5961/D5961M-17, 2017
[24] PIERRON F, CERISIER F, GREDIAC M. A numerical and experimental study of woven composite pin-joints[J]. Journal of Composite Materials, 2000, 34(12):1028-1054
[25] HASHIN Z, ROTEM A. A fatigue failure criterion for fiber reinforced materials[J]. Journal of Composite Materials, 1973, 7(4):448-464
[26] 张洁. 复合材料铺层设计准则的一些理解[J]. 科技创新导报, 2013(14):57-58 ZHANG Jie. Some understanding of pavement design criterion for composite material[J]. Science and Technology Innovation Herald, 2013(14):57-58(in Chinese) |
|
|
|
相关文献: |
|
|
1．拓宏亮, 马晓平, 卢智先.基于连续介质损伤模型的复合材料连接件失效分析[J]. 西北工业大学学报, 2018,36(5): 848-855 |
|
|
|
|
|
|
