|
|
论文:2019,Vol:37,Issue(5):1053-1059 |
|
|
引用本文： |
|
|
薛克敏, 吴超, 杨卫正, 代光旭, 李萍, 严思梁. 扭转减振器壳体带轮旋弯成形工艺研究[J]. 西北工业大学学报 |
|
|
XUE Kemin, WU Chao, YANG Weizheng, DAI Guangxu, LI Ping, YAN Siliang. Study on Rotary Bending Forming Process of Torsional Damper Shell Pulley[J]. Northwestern polytechnical university |
|
|
|
|
|
|
|
| 扭转减振器壳体带轮旋弯成形工艺研究 |
|
| 薛克敏, 吴超, 杨卫正, 代光旭, 李萍, 严思梁 |
|
| 合肥工业大学 材料科学与工程学院, 安徽 合肥 230009 |
| 摘要: |
| 针对具有特征结构的扭转减振器壳体带轮的整体成形工艺研究，对壳体带轮这类回转体零件的生产与开发具有重要意义。提出一种结合板材旋弯成形工艺和旋轮结构设计，整体成形扭转减振器壳体带轮。通过有限元模拟，建立两道次旋弯成形模型，旋轮沿径向进给过程中，使板坯外缘发生压缩增厚和弯曲聚料后的二次增厚，并采用标记点法分析变形区等效应力和材料流动。结合壳体带轮结构特点，提出一种"旋弯增厚、聚料增厚"旋轮结构设计准则，通过旋轮特征结构有效控制变形区金属流动，由此获得用于成形多楔齿的特定区域。对成形过程中零件瞬时截面的定量分析，结合旋轮结构设计准则和材料流动速率，确定旋轮弧面半径和圆心角。在目标成形工艺参数下，有限元数值模拟和试验结果基本一致，凸筋成形饱满，特征区域增厚到最小厚度值，验证了金属板材旋弯成形理论和旋轮结构设计准则的可行性。 |
| 关键词:
扭转减振器
旋弯成形
旋轮结构
材料流动
有限元数值模拟
|
|
| Study on Rotary Bending Forming Process of Torsional Damper Shell Pulley |
|
| XUE Kemin, WU Chao, YANG Weizheng, DAI Guangxu, LI Ping, YAN Siliang |
|
| School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009, China |
| Abstract: |
| To study the integral forming process of torsion damper shell pulley with characteristic structure is of great significance for producing and developing of the rotational part such as shell pulley. A processing way was proposed by combining plate bending forming and roller structure design, to integral forming torsion damper shell pulley. A model for two-step bending forming was establishedvia finite element method. Under the radial feeding of roller, the outer edge of plate was subjected to compress thickening and secondary thickened after bending, and effective stress and metal flow in the deformation zone were analyzed by using marking point. Combining with the structural characteristics of shell pulley, a design criterion "rotating thickening, gathering thickening" of roller was proposed. The metal flow in deformation zone was effectively controlled through the characteristic structure of roller, thereby the specific region to forming multi-wedge toothwas obtained. The quantitative analysis of the instantaneous part section in the forming process, combining with the design criteria of roller structure and material flow rate, radius and arc angle of roller were determined. With the objective forming parameters, the comparison between the simulation results and the experimental are basically coincided, the ribs were fully formed and the specific regions was thickened to minimum value, which verified the feasibility of sheet-bulk metal rotary bending forming theory and the design criterion of roller structure. |
| Key words:
torsional damper
rotary bending forming
structure of roller
material flow
FE simulation
|
|
| 收稿日期: 2018-10-09
修回日期:
|
| DOI: 10.1051/jnwpu/20193751053 |
| 基金项目: 江苏省科技计划项目（BA2016047）与江苏省南通市科技计划项目（GY22015008）资助 |
| 通讯作者:
Email： |
| 作者简介: 薛克敏(1963-),合肥工业大学教授、博士生导师,主要从事精密塑性成形及组织性能研究。
|
|
| 相关功能 |
|
|
|
|
| 作者相关文章 |
|
| 薛克敏 在本刊中的所有文章 |
| 吴超 在本刊中的所有文章 |
| 杨卫正 在本刊中的所有文章 |
| 代光旭 在本刊中的所有文章 |
| 李萍 在本刊中的所有文章 |
| 严思梁 在本刊中的所有文章 |
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] 孙哲. 基于多目标拓扑优化的汽车零件轻量化设计[D]. 武汉:华中科技大学,2014 SUN Zhe. Lightweight Design of Auto Parts Based on Multi-Objective Topology Optimization[D]. Wuhan, Huazhonguniversity of Science and Technology, 2014(in Chinese)
[2] 王成和,刘克璋,周路. 旋压技术[M]. 福建:福建科学技术出版社,2017 WANG Chenghe, LIU Kezhang, ZHOU Lu. Rotary Technology[M]. Fujian, Fujian Press of Science and Technology, 2017(in Chinese)
[3] MERKLEIN M, KOCH J, OPEL S, et al. Fundamental Investigations on the Material Flow at Combined Sheet and Bulk Metal Forming Processes[J]. CIRP Annals-Manufacturing Technology, 2011, 60:283-286
[4] TAN C J, MORI K, ABE Y, et al. Forming of Tailored Blanks Having Local Thickening for Control of Wall Thickness of Stamped Product[J]. Journal of Materials Processing Technology, 2008, 202:443-449
[5] MORI K, ABE Y, OSAKADA K, et al. Plate Forging of Tailored Blanks Having Local Thickening for Deep Drawing of Square Cups[J]. Journal of Materials Processing Technology, 2011, 211:1569-1574
[6] XIA Q X, XIAO G F, LONG H, et al. A Review of Process Advancement of Novel Metal Spinning[J]. International Journal of Machine Tools & Manufacture, 2014, 85:100-121
[7] 万里翔,郑帮智,上官文斌,等. 发动机附件多楔带轮旋压成形仿真方法[J]. 华南理工大学学报, 2016,44(3):81-87 WAN Lixiang, ZHENG Bangzhi, SHANGGUAN Wenbin, et al. Simulation Method of Spinning Forming of Multi-Wedge Belt Wheel as Engine Accessory[J]. Journal of South China University of Technology, 2016, 44(3):81-87(in Chinese)
[8] 王甲子. 多楔带轮旋压成形方法及工艺研究[D]. 广州:华南理工大学,2009 WANG Jiazi. Study on Spinning Forming Method and Process of Multi-Wedge Belt Pulley[D]. Guangzhou, South China University of Technology, 2009(in Chinese)
[9] 胡运展,金俊松,王新云,等. 盘形件局部加热旋压增厚过程设计[J]. 塑性工程学报,2017, 24(1):9-14 HU Yunzhan, JIN Junsong, WANG Xinyun, et al. Process Design for Local Heating Rotary Thickening of Disc-Like Blanks[J]. Journal of Plasticity Engineering, 2014, 24(1):9-14(in Chinese)
[10] JIANG Z Q, YANG H, ZHAN M, et al. Coupling Effects of Material Properties and the Bending Angle on the Springback Angle of a Titanium Alloy Tube During Numerically Controlled Bending[J]. Materials and Design, 2010, 31:2001-2010
[11] NAN Liu, HE Yang, HENG Li, et al. An Imperfection-Based Perturbation Method for Plastic Wrinkling Prediction in Tube Bending under Multi-Die Constraints International[J]. Journal of Mechanical Sciences, 2015, 98:178-194
[12] GAN Y, TIAN Z, DONG H, et al. Chinese Materials Engineering Dictionary[J]. Chemical Industry Press, 2006, 263
[13] 路平,张云开,陈波. 汽车轮辐错距强力旋压成形的有限元仿真[J]. 上海交通大学学报, 2015,49(1):56-61 LU Ping, ZHANG Yunkai, CHEN Bo. Finite Element Method Simulation of Stagger Power Spinning Forming of Automobile Spoke[J]. Journal of Shanghai Jiaotong University, 2015, 49(1):56-61(in Chinese)
[14] 詹梅,郭靖,陈飞,等. 带横向内筋特征构件外强旋压成形机理研究[J]. 西北工业大学学报, 2014, 32(5):799-804 ZHAN Mei, GUO Jing, CHEN Fei, et al. Exploring Forming Mechanism of a Part with Transverse Inner Rib during Power Spinning[J]. Journal of Northwestern PolytechnicalUniversity, 2014, 32(5):799-804(in Chinese)
[15] MUSIC O, ALLWOOD J M, KAWAI K. A Review of the Mechanics of Metal Spinning[J]. Journal of Materials Processing Technology, 2010, 210:3-23
[16] ROY M J, KLASSEN R J, WOOD J T. Evolution of Plastic Strain during a Flow Forming Process[J]. Journal of Materials Processing Technology, 2009, 209:1018-1025 |
|
|
|
|
|
|
|
