|
|
论文:2019,Vol:37,Issue(3):628-635 |
|
|
引用本文： |
|
|
颜新宇, 王守仁, 温道胜, 王高琦, 刘文涛. HfC颗粒对WC/Co复合材料裂纹萌生和扩展行为的影响[J]. 西北工业大学学报 |
|
|
YAN Xinyu, WANG Shouren, WEN Daosheng, WANG Gaoqi, LIU Wentao. Effects of HfC Particles on Crack Initiation and Propagation Behavior of WC/Co Composites[J]. Northwestern polytechnical university |
|
|
|
|
|
|
|
| HfC颗粒对WC/Co复合材料裂纹萌生和扩展行为的影响 |
|
| 颜新宇, 王守仁, 温道胜, 王高琦, 刘文涛 |
|
| 济南大学 机械工程学院, 山东 济南 250022 |
| 摘要: |
| 以提高材料的韧性为目的，通过冷压、热压工艺制备出碳化钨基复合材料，对其断裂韧性、弯曲强度进行测试；利用SEM对HfC/WC/Co复合材料的微观形貌进行观察；基于裂纹扩展能量释放公式，构建了裂纹直行、裂纹偏转和裂纹分叉的应力强度因子与裂纹长度的数学模型；借助仿真软件ABAQUS对裂纹直行、裂纹偏转、裂纹分叉、裂纹钉扎4种裂纹扩展方式进行了仿真验证；结果表明：添加适量的HfC可以有效改善复合材料的断裂韧性和弯曲强度；HfC和Co在基体中均匀分布，对复合材料强度和韧性的提高具有明显作用，改善机制为裂纹偏转、裂纹分叉、裂纹钉扎、穿晶断裂等协同作用将裂纹扩展尖端的应力分散或转移到HfC上，从而降低基体中裂纹尖端的应力集中，提高复合材料的韧性。 |
| 关键词:
碳化铪
裂纹扩展
能量释放率
增强增韧
ABAQUS
|
|
| Effects of HfC Particles on Crack Initiation and Propagation Behavior of WC/Co Composites |
|
| YAN Xinyu, WANG Shouren, WEN Daosheng, WANG Gaoqi, LIU Wentao |
|
| School of Mechanical Engineering, Jinan University, Jinan 250022, China |
| Abstract: |
| Tungsten carbide composites were prepared by cold-pressing and hot-pressing sintering; fracture toughness and bending strength of the specimens were tested. The microstructures of HfC/WC/Co composites were observed with the SEM. The mathematical models were established to investigate the relationship between stress intensity factors of crack straight-through, crack deflection, and crack bifurcation with crack length, based on the crack propagation energy release rate. The simulation software ABAQUS was used to verify the four crack propagation methods of crack straight-through, crack deflection, crack bifurcation and crack pinning. The simulation results show that adding appropriate amount of HfC can effectively improve the fracture toughness and bending strength of the composites. The homogeneous distribution of HfC and Co in the matrix has a significant effect on the improvement of the strength and toughness of the composites, and the improvement mechanism is to disperse or transfer the stress at the crack tip to HfC by crack deflection, crack bifurcation, crack pinning, transcrystalline fracture, etc. As a result, the stress concentration at the crack tip in the matrix is reduced, and the toughness of the composites is improved. |
| Key words:
ABAQUS
crack tips
HfC particle
crack propagation
energy release rate
toughening
|
|
| 收稿日期: 2018-07-15
修回日期:
|
| DOI: 10.1051/jnwpu/20193730628 |
| 基金项目: 国家自然科学基金（51872122）与泰山学者工程专项经费（2016-2020）资助 |
| 通讯作者:
Email： |
| 作者简介: 颜新宇(1992-),济南大学硕士研究生,主要从事金属复合材料及摩擦磨损研究。
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] 张栋梁, 莫蓉, 孙惠斌, 等. 基于流形学习与隐马尔可夫模型的刀具磨损状况识别[J]. 西北工业大学学报, 2015, 33(4):651-657 ZHANG Dongliang, MO Rong, SUN Huibin, et al. Tool Wear Condition Monitoring Based on Manifold Learning and Hidden Markov Model[J]. Journal of Northwestern Polytechnical University, 2015, 33(4):651-657(in Chinese)
[2] 伍俏平,刘平,邓朝晖,等. 基于超细晶硬质合金钻头的AFRP钻削性能[J]. 复合材料学报, 2017, 34(10):2246-2253 WU Qiaoping, LIU Ping, DENU Zhaohui, et al. Drilling Performance of Ultraline Cemented Carbide Drill in Machining Aramid Fiber Reinforced Polymer Composites[J]. Acta Materiae Compositae Sinica, 2017, 34(10):2246-2253(in Chinese)
[3] GAO Yang, YAN Mingyuan, LUO Binghui. Effects of NbC Additions on the Microstructure and Properties of Non-Uniform Structure WC-Co Cemented Carbides[J]. Materials Science and Engineering, 2017, 287:259-268
[4] DONG Weiwei, ZHU Shigen, BAI Tao. Influence of Al2O3 Whisker Concentration on Mechanical Properties of WC-Al2O3 Whisker Composite[J]. Ceramics International, 2015, 41(10):13685-13691
[5] 高姣姣,宋金鹏,王金龙,等. 短切碳纤维含量对WC基复合陶瓷刀具材料微观组织及力学性能的影响[J]. 热加工工艺, 2017, 46(16):108-111 GAO Jiaojiao, SONG Jinpeng, WANG Jinlong, et al. Effects of Short-Cut Carbon Fiber Content on Microstructure and Mechanical Properties of WC-Based Composite Ceramic Cutting Tool Materials[J]. Hot Working Technology, 2017, 46(16):108-111(in Chinese)
[6] ZHENG Donghai, LI Xiaoqiang, LI Yuanyuan. Zirconia-Toughened WC with/without VC and Cr3C2[J]. Ceramics International, 2014, 40(1):2011-2016
[7] LEI Yiwen, SUN Jing, DU Xiwen, et al. Properties and Microstructure of VC/Cr3C2-Doped WC/Co Cemented Carbides[J]. Rare Metals, 2007, 26(6):584-590
[8] SU Wei, SUN Yexi, YANG Hailin. Effects of TaC on Microstructure and Mechanical Properties of Coarse Grained WC-9Co Cemented Carbides[J]. Trans of Nonferrous Metals Society of China, 2015, 25(4):1194-1199
[9] NINO A, Yuma I, Takashi S. Effects of ZrC and SiC Addition on the Microstructures and Mechanical Properties of Binderless WC[J]. International Journal of Refractory Metals and Hard Materials, 2017, 69:259-265
[10] SIWAK P, GARBIEC D. Microstructure and Mechanical Properties of WC-Co, WC-Co-Cr3C2 and WC-Co-TaC Cermets Fabricated by Spark Plasma Sintering[J]. Trans of Nonferrous Metals Society of China, 2016,26(10):2641-2646
[11] 高姣姣,姜龙凯,宋金鹏,等. TiC含量对WC-TiC-TaC硬质合金材料微观组织及力学性能的影响[J]. 无机材料学报, 2017, 32(8):891-896 GAO Jiaojiao, JIANG Longkai, SONG Jinpeng, et al. Effects of TiC Content on Microstructure and Mechanical Properties of WC-TiC-TaC Cemented Carbide Materials[J]. Journal of Inorganic Materials, 2017, 32(8):891-896(in Chinese)
[12] 韩小伟,夏小群. VC含量对WC-12%Co硬质合金性能的影响[J]. 装备制造技术, 2017(1):106-108 HAN Xiaowei, XIA Xiaoqun. Influence of VC Content on Properties of WC-12%Co Cemented Carbide[J]. Equipment Manufacturing Technology, 2017(1):106-108(in Chinese)
[13] 郑虎春,范景莲,杨文华,等. VC/Cr3C2及配碳量对WC-0.5Co超细硬质合金组织与性能的影响[J]. 稀有金属材料与工程, 2015, 44(4):912-917 ZHENG Huchun, FAN Jinglian, YANG Wenhua, et al. Effects of VC/Cr3C2 and the Amount of Carbon on Microstructure and Properties of WC-0.5Co Ultra-Fine Cemented Carbide[J]. Rare Metal Materials and Engineering, 2015, 44(4):912-917(in Chinese)
[14] ZHOU Wei, XIONG Ji, WAN Weicai. The Effect of NbC on Mechanical Properties and Fracture Behavior of WC-10Co Cemented Carbides[J]. International Journal of Refractory Metals and Hard Materials, 2015, 50:72-78
[15] LUDOVIC C, MARIANNE B P, SANS J L. Effect of High Temperature Oxidation on the Radiative Properties of HfC-Based Ceramics[J]. Corrosion Science, 2017, 126:55-264
[16] GAO Jie, HONG Jun, ZHENG Heike, et al. Design and Synthesis of Diffusion-Modified HfC/HfC-SiC Bilayer System onto WC-Co Substrate for Adherent Diamond Deposition[J]. Journal of Alloys and Compounds, 2017, 705:376-383
[17] 王守仁,王高琦,杨学锋,等. 基于第一抗热震因子的BN纳米管/Si3N4复合材料抗热震性能评价[J]. 复合材料学报, 2017,34(7):1575-1581 WANG Shouren, WANG Gaoqi, YANG Xuefeng, et al. Evaluation of Thermal Shock Resistance of BNNTs/Si3N4 Composites Based on the Second Heat Shock Factor[J]. Acta Materiae Compositae Sinica, 2017, 34(7):1575-1581(in Chinese)
[18] XIE D A. HILLS, Quasibrittle Fracture Beneath a Flat Bearing Surface[J]. Engineering Fracture Mechanics, 2008, 75:1223-1230
[19] 朱有利,侯帅,王燕礼,等. 基于最大能量释放率原理的裂纹扩展算法的改进[J]. 机械工程学报, 2016, 52(10):91-96 ZHU Youli, HOU Shuai, WANG Yanli, et al. Improvement of Crack Propagation Algorithm Based on Maximum Energy Release Rate Principle[J]. Chinese Journal of Mechanical Engineering, 2016, 52(10):91-96(in Chinese)
[20] 殷之平, 郭今, 黄其青. 基于材料各向异性的整体梁裂纹转折分析[J]. 西北工业大学学报, 2012, 30(2):160-164 YIN Zhiping, GUO Jin, HUANG Qiqing. Analyzing Crack Turn of Wing-Beam Integrated Structure Based on Anisotropic Mechanical Properties of Aluminum Alloy[J]. Journal of Northwestern Polytechnical University, 2012, 30(2):160-164(in chinese)
[21] TORRES Y, TARRAGO J M, COUREAUX D. Fracture and Fatigue of Rock Bit Cemented Carbides:Mechanics and Mechanisms of Crack Growth Resistance under Monotonic and Cyclic Loading[J]. International Journal of Refractory Metals and Hard Materials, 2014, 45:179-188
[22] LI Tao, LI Qingfa, Fuh J Y H. Effects of AGG on Fracture Toughness of Tungsten Carbide[J]. Materials Science and Engineering, 2007, 445/446:587-592 |
|
|
|
相关文献: |
|
|
1．何龙龙, 刘志芳, 顾俊杰, 王金亮, 门坤发.基于XFEM的疲劳裂纹扩展路径和寿命预测[J]. 西北工业大学学报, 2019,37(4): 737-743 |
|
|
2．束一秀, 李亚智, 姜薇, 贾雨轩.基于扩展有限元的多裂纹扩展分析[J]. 西北工业大学学报, 2015,33(2): 197-203 |
|
|
3．夏仲纯, 马玉娥, 云双, 熊晓枫.玻璃纤维增强铝合金层板的裂纹扩展特性研究[J]. 西北工业大学学报, 2013,31(6): 891-895 |
|
|
|
|
|
|
