论文:2018,Vol:36,Issue(5):848-855
引用本文:
拓宏亮, 马晓平, 卢智先. 基于连续介质损伤模型的复合材料连接件失效分析[J]. 西北工业大学学报
Tuo Hongliang, Ma Xiaoping, Lu Zhixian. Failure Analysis of Composite Pinned Joints Based on Continuum Damage Mechanics[J]. Northwestern polytechnical university

基于连续介质损伤模型的复合材料连接件失效分析
拓宏亮1, 马晓平1,2, 卢智先1
1. 西北工业大学 航空学院, 陕西 西安 710072;
2. 中国科学院 工程热物理研究所, 北京 100190
摘要:
对4种不同铺层顺序的复合材料销钉连接件进行了挤压试验,得到复合材料销钉连接件的挤压强度和弦向挤压刚度,分析了载荷方向偏角对失效模式、挤压强度和弦向挤压刚度的影响规律。基于连续介质损伤力学理论,建立了复合材料销钉连接件在挤压载荷下的三维非线性数值模型,其中,采用最大应变准则预测纤维损伤的萌生,损伤演化规律则采用双线性损伤本构关系。基于物理失效机制的Puck准则对基体损伤的起始进行判定,根据断裂面内的等效应变表征基体损伤的扩展。该模型还考虑了剪切非线性和就地强度效应对挤压强度和损伤扩展的影响。基于此模型分析了销钉连接件在挤压载荷下的失效模式、挤压强度和弦向挤压刚度。试验结果和计算结果较好吻合,验证了模型的准确性和适用性。
关键词:    复合材料    销钉连接    挤压强度    连续介质损伤力学    损伤扩展    有限元模型   
Failure Analysis of Composite Pinned Joints Based on Continuum Damage Mechanics
Tuo Hongliang1, Ma Xiaoping1,2, Lu Zhixian1
1. School of Aeronautics, Northwestern Polytechnical University, Xi'an 710072, China;
2. Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
Abstract:
The paper conducted bearing tests on composite pinned joints with four different stacking sequences. The bearing strength and bearing chord stiffness were obtained. The influence of stacking sequences on failure modes, bearing strength and bearing chord stiffness was discussed. Based on continuum damage mechanics, a three-dimensional finite element model of composite pinned joint under bearing load was built, where the maximum strain criterion was employed for initiation and bi-liner damage constitutive relation for revolution of fiber damage, while the physical-based Puck criterion was used for matrix damage initiation, and matrix damage revolution depended on the effective strain on the fracture plane. The failure mode, bearing strength and bearing chord stiffness of composite pinned joint were discussed with this model under which the non-linear shear behavior and in-situ strength effects were considered. Good agreements between test results and numerical simulations validates the accuracy and applicability of the finite element model.
Key words:    composite materials    composite pinned joint    bearing strength    continuum damage mechanics    damage evolution    finite element model   
收稿日期: 2017-09-09     修回日期:
DOI:
基金项目: 中央高校基本科研专项资金(3102017zy046)资助
通讯作者:     Email:
作者简介: 拓宏亮(1989-),西北工业大学博士研究生,主要从事复合材料结构强度和疲劳寿命研究。
相关功能
PDF(1904KB) Free
打印本文
把本文推荐给朋友
作者相关文章
拓宏亮  在本刊中的所有文章
马晓平  在本刊中的所有文章
卢智先  在本刊中的所有文章

参考文献:
[1] Vmran Esendemir. An Experimental Study of Mechanically Fastened Composite Joints with Clearance[J]. International Journal of Damage Mechanics, 2011, 20(3):464-480
[2] Chang F K, Lessard L B. Damage Tolerance of Laminated Composites Containing an Open Hole and Subjected to Compressive Loadings:Part I-Analysis[J]. Journal of Composite Materials, 1991, 25(1):44-64
[3] Camanho P P, Matthews F L. A Progressive Damage Model for Mechanically Fastened Joints in Composite Laminates[J]. Journal of Composite Materials, 1999, 33(24):2248-2280
[4] Tserpes K I, Papanikos P, Kermanidis T. A three-Dimensional Progressive Damage Model for Bolted Joints in Composite Laminates Subjected to Tensile Loading[J]. Fatigue & Fracture of Engineering Materials & Structures, 2010, 24(10):663-675
[5] Olmedo A, Santiuste C, Barbero E. An Analytical Model for Predicting the Stiffness and Strength of Pinned-Joint Composite Laminates[J]. Composites Science & Technology, 2014, 90(90):67-73
[6] Dano M L, Gendron G, Picard A. Stress and Failure Analysis of Mechanically Fastened Joints in Composite Laminates[J]. Composite Structures, 2000, 50(3):287-296
[7] Zhou Y, Nezhad H Y, Hou C, et al. A three Dimensional Implicit Finite Element Damage Model and Its Application to Single-Lap Multi-Bolt Composite Joints with Variable Clearance[J]. Composite Structures, 2015, 131:1060-1072
[8] Zhou Y, Yazdani-Nezhad H, Mccarthy M A, et al. A Study of Intra-Laminar Damage in Double-Lap, Multi-Bolt, Composite Joints with Variable Clearance Using Continuum Damage Mechanics[J]. Composite Structures, 2014, 116(1):441-452
[9] Bodjona K, Lessard L. Nonlinear Static Analysis of a Composite Bonded/Bolted Single-Lap Joint Using the Mesh-Free Radial Point Interpolation Method[J]. Composite Structures, 2015, 134:1024-1035
[10] Tang Y, Zhou Z, Pan S, et al. Mechanical Property and Failure Mechanism of 3D Carbon-Carbon Braided Composites Bolted Joints under Unidirectional Tensile Loading[J]. Materials & Design, 2015, 65(65):243-253
[11] 李璇,陈秀华,史晓辉,等.考虑双模量影响的复合材料销钉连接失效分析[J].上海交通大学学报,2015,49(1):101-108 Li Xuan, Chen Xiuhua, Shi Xiaohui, et al. Effect of Bimodularity on Failure Behaviors of Pinned-Joint Composite Laminates[J]. Journal of Shanghai Jiaotong University, 2015,49(1):101-108(in Chinese)
[12] 魏景超,矫桂琼,闫照明,等. 单面螺纹抽钉干涉配合复合材料连接件挤压强度研究[J]. 航空学报, 2013, 34(7):1627-1635 Wei Jingchao, Jiao Guiqiong, Yan Zhaoming, et al. Bearing Strength of Composite Joints Interference-Fitted with Blind Bolts[J]. Acta Aeronauticaet Astronsutica Sinica, 2013,34(7):1627-1635(in Chinese)
[13] 刘向东,李亚智,苏杰,等. 一种预估复合材料钉-孔挤压强度与刚度的方法[J]. 航空材料学报, 2014, 34(5):81-87 Liu Xiangdong, Li Yazhi, Su Jie, et al. A Method to Evaluate Bearing Strength and Stiffness of Composite Joints[J]. Journal of Aeronautical Materials, 2014,34(5):81-87(in Chinese)
[14] 刘向东,李亚智,李彪,等. 复合材料机械连接数值模型和强度研究[J]. 西北工业大学学报, 2013, 31(6):878-883 Liu Xiangdong, Li Yazhi, Li Biao, et al. On Numeric al Modeling and Tensile Strength of Bolted Composite Joints[J]. Journal of Northwestern Polytechnical University, 2013, 31(6):878-883(in Chinese)
[15] Hahn H T, Tsai S W. Nonlinear Elastic Behavior of Unidirectional Composite Laminates[J]. Journal of Composite Materials, 1973, 7(1):102-118
[16] Puck A, Schürmann H. Failure Analysis of FRP Laminates by Means of Physically Based Phenomenological Models[J]. Composites Science & Technology, 2002, 62(12):1633-1662