|
|
论文:2018,Vol:36,Issue(1):66-73 |
|
|
引用本文： |
|
|
黄河源, 赵美英, 万小朋, 侯赤. 一种复合材料螺栓连接结构非线性刚度模型及应用[J]. 西北工业大学学报 |
|
|
Huang Heyuan, Zhao Meiying, Wan Xiaopeng, Hou Chi. A Composite Bolted Joints Non-Linear Stiffness Model and its Application[J]. Northwestern polytechnical university |
|
|
|
|
|
|
|
| 一种复合材料螺栓连接结构非线性刚度模型及应用 |
|
| 黄河源, 赵美英, 万小朋, 侯赤 |
|
| 西北工业大学 航空学院, 陕西 西安 710072 |
| 摘要: |
| 针对复合材料螺栓连接结构挤压破坏及钉载分配规律，提出一种非线性刚度模型。基于单钉连接结构试验获得的应力-应变曲线，将连接结构挤压破坏过程分为：线性无损伤阶段、非线性损伤扩展阶段和线性退化阶段，并将连接结构等效为弹簧系统模型。模型在线性阶段考虑了层合板间摩擦力的影响；在非线性阶段考虑了层合板面内剪切非线性并定义了非线性损伤函数；在线性退化阶段基于能量吸收原理，对结构失效后力学行为进行了表征。最后，将单钉弹簧模型引入多钉连接结构进行分析，通过多钉连接结构试验验证表明，模型计算结果与试验曲线吻合良好，钉载分配计算误差小，符合工程要求。 |
| 关键词:
复合材料
刚度模型
多钉螺栓连接
试验设计
弹簧模型
非线性
应力-应变关系
|
|
| A Composite Bolted Joints Non-Linear Stiffness Model and its Application |
|
| Huang Heyuan, Zhao Meiying, Wan Xiaopeng, Hou Chi |
|
| School of Aeronautics, Nothwestern Polytechnical University, Xi'an 710072, China |
| Abstract: |
| The paper presents a nonlinear stiffness model on the bearing damage and bolt-load distribution rule of composite bolted joints. Based on the experimental stress-strain curves of composite single-bolted joints, the bearing damage process of structures can be divided into:linear non-damage stage; nonlinear damage propagation stage and linear degeneration stage. In this paper, the composite bolted joints are represented by a system of springs in which the static friction effects between laminates are considered in the linear stage, the non-linear interlaminate shear behavior and the nonlinear damage function for composite are defined and failure behavior based on the energy abortion principle is simulated in the linear degeneration stage. At last, the multi-fasters spring model is analyzed by importing the single-faster spring model.Comparing with the experimental data of multi-fasters shows the numerical result is in good agreement with experimental curves and has little error on the bolt-load distribution, which satisfies to the requirements in the engineering. |
| Key words:
composites
stiffness model
multi-fasters joint
design of experimental
spring model
non-linear
stress-strain curves
|
|
| 收稿日期: 2017-03-12
修回日期:
|
| DOI: |
| 通讯作者:
Email： |
| 作者简介: 黄河源(1988-),西北工业大学博士生,主要从事飞机结构设计、复合材料结构设计与分析研究。
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] Ireman T, Ranvik T, Eriksson I. On Damage Development in Mechanically Fastened Composite Laminates[J]. Composite Structures, 2000, 49(2):151-171
[2] Lawlor V P, Mccarthy M A, Stanley W F. An Experimental Study of Bolt-Hole Clearance Effects in Double-Lap, Multi-Bolt Composite Joints[J]. Composite Structures, 2005, 71(2):176-190
[3] Xiao Y, Ishikawa T. Bearing Strength and Failure Behaviour of Bolted Composite Joints (PartⅡ:Modelling and Simulation)[J]. Compos Sci Technol, 2005, 65(78):1032-1043
[4] Zhou Y H, Hamed Y N, Chi H, et al. A Three Dimensional Implicit Finite Element Damage Model and its Application to Single-Lap Multi-Bolt Composite Joints with Variable Clearance[J]. Composite Structures, 2015, 131(11):1060-1072
[5] Santiuste C, Barbero E, Miguelez M H. Computational Analysis of Temperature Effect in Composite Bolted Joints for Aeronautical Applications[J]. Reinf Plast Compos, 2011, 30(1):3-11
[6] Camanho P P, Matthews F L. A Progressive Damage Model for Mechanically Fastened Joints in Composite Laminates[J]. Composite Material, 1999, 33(24):2248-2280
[7] 王丹勇,温卫东,崔海涛. 复合材料单钉接头三维逐渐损伤破坏分析[J]. 复合材料学报,2005, 22(3):168-174 Wang Danyong, Wen Weidong, Cui Haitao. Three-Dimensional Progressive Damage Analysis of Single Fastener Joints in Composite Laminates[J]. Acta Materiae Compositae Sinica, 2005,22(6):168-174(in Chinese)
[8] 朱智毅. 复合材料厚板螺栓连接挤压强度研究[D]. 南京:南京航空航天大学,2014 Zhu Zhiyi. Research on Bearing Strength of Bolted Joints between Thick Composite Laminates[D]. Nanjing, Nanjing University of Aeronautics and Astronautics, 2014(in Chinese)
[9] Tate M B, Rosenfeld S J. Preliminary Investigation of the Loads Carried by Individual Bolts in Bolted Joints[R]. NACA TN-1051IR-1946
[10] Nelson W D, Bunin B L, Hart-Smith L J. Critical Joints in Large Composite Aircraft Structure[R]. NASA CR-3710-1983
[11] McCarthy M A, McCarthy C T, Padhi G S. A Simple Method for Determining the Effects of Bolt-Hole Clearance on Load Distribution in Single-Column, Multi-Bolt Composite Joints[J]. Composite Structures, 2006, 73(1):78-87
[12] McCarthy C T, Gray P J. An Analytical Model for the Prediction of Load Distribution in Highly Torqued Multi-Bolt Composite Joints[J]. Composite Structures, 2011, 93(2):287-298
[13] 谢宗蕻,李想,杨淋雅,等. 基于弹簧质量模型的复合材料螺接修理载荷传递计算方法[J]. 航空学报.2016, 37(12):3742-3751 Xie Zonghong, Li Xiang, Yang Linya, et al. A Calculation Method for Load Transfer in Bolted Repair of Composite Laminates Based on Spring-Mass Mode[J]. Acta Aeronautica et Astronautica Sinica, 2016, 37(12):3742-3751(in Chinese)
[14] Olmedo A, Santiuste C, Barbero E. An Analytical Model for Predicting the Stiffness and Strength of Pinned-Joint Composite Laminates[J]. Composites Science and Technology, 2014, 90(1):67-73
[15] 谢鸣九. 复合材料连接[M]. 上海:上海交通大学出版社,2011:174-176 Xie M J. Joints for Composite Materials Book[M]. Shanghai, Shanghai Jiaotong University Press, 2011:174-176(in Chinese)
[16] Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates[S]. ASTM-D5961/D5961M-13-B, 2013
[17] Mcsarthy C T, O'higgins R M, Frizzell R M. A Cubic Spline Implementation of Non-Linear Shear Behaviour in Three-Dimensional Progressive Damage Models for Composite Laminates[J]. Composite Structures, 2010, 92(1):173-181
[18] Sharos P A, Egan B, Mcsarthy C T. An Analytical Model for Strength Prediction in Multi-Bolt Composite Joints at Various Loading Rates[J]. Composite Structures, 2014, 116(1):300-310
[19] Mcsarthy C T, Mccarthy M A, Stanley W F, et al. Experiences with Modeling Friction in Composite Bolted Joints[J]. Journal of Composite Material, 2005, 39:1881-1908 |
|
|
|
|
|
|
|
