凸形极靴表贴式永磁磁极同步电机性能优化

刘露; 刘坤; 张羽丰; 魏玖存

doi:10.13433/j.cnki.1003-8728.20190173

凸形极靴表贴式永磁磁极同步电机性能优化

doi: 10.13433/j.cnki.1003-8728.20190173

山东理工大学交通与车辆工程学院, 山东淄博 255049

基金项目:

国家自然科学基金项目 51775320

国家自然科学基金项目 51875327

详细信息

作者简介:
刘露(1972-), 讲师, 博士, 研究方向为结构的分析计算, 935539808@qq.com

中图分类号: TM743;TP391.9
计量
- 文章访问数: 499
- HTML全文浏览量: 472
- PDF下载量: 27
- 被引次数: 0
出版历程
- 收稿日期: 2019-05-13
- 刊出日期: 2019-10-05

Performance Optimization of Synchronous Motor with Surface-mounted Permanent Magnet Poles and Convex Pole Shoes

School of Transportation and Vehicle Engineering, Shandong University of Technology, Shandong Zibo 255049, China

摘要

摘要: 针对表贴式永磁同步电机空载径向气隙磁密波形正弦性差导致电机反电势波形畸变，影响电机输出性能，改良的复杂结构的永磁钢导致加工成本提高的问题，提出一种表贴式矩形永磁钢加装凸形极靴的新型磁极结构。利用有限元软件建立3相18极54槽永磁同步电机，研究极靴参数对永磁同步电机空载径向气隙磁密、空载反电势、齿槽转矩和永磁钢涡流损耗的影响规律，获得最优极靴参数。输出特性对比分析可得，加装极靴的新型磁极电机空载反电势波形正弦性明显提高，齿槽转矩和永磁钢涡流损耗大幅度降低，电机输出性能显著改善。
- 表贴式永磁钢 /
- 同步电机 /
- 凸形极靴 /
- 性能优化
Abstract: Aiming at the poor sinusoidal no-load radial air-gap magnetic density waveform for affecting the distortion of back electromotive force and the output performance of the surface-mounted permanent magnet synchronous motor, and improving the processing costs of the permanent magnet steels with complex structures, a new magnetic pole structure with rectangular permanent magnet steel and convex pole shoe is proposed. The optimum parameters of the pole shoe are obtained by analyzing the influence of the pole shoe parameters on the no-load radial air-gap magnetic density, no-load back electromotive force, cogging torque and permanent magnet steel's eddy current loss by using 3 phases, 18 poles and 54 slot permanent magnet generator simulation model established via finite element simulation software. And the comparison results of output characteristics show that the new magnetic pole with convex pole shoe can make the sinusoidal performance of back electromotive force waveform obviously improved, cogging torque and permanent magnet steel's eddy current loss greatly reduced, and motor output performance significantly improved.
- surface-mounted permanent magnet steel /
- synchronous motors /
- convex pole shoe /
- performance optimization

HTML全文

图 1 表贴式永磁同步电机转子磁极结构图

下载: 全尺寸图片幻灯片

图 2 表贴式永磁同步电机径向气隙磁密波形图

下载: 全尺寸图片幻灯片

图 3 加装凸形极靴永磁同步电机磁极结构图

下载: 全尺寸图片幻灯片

图 4 新型磁极结构参数图

下载: 全尺寸图片幻灯片

图 5 空载径向气隙磁密波形变化

下载: 全尺寸图片幻灯片

图 6 空载径向气隙磁密波形THD变化

下载: 全尺寸图片幻灯片

图 7 空载反电势波形变化

下载: 全尺寸图片幻灯片

图 8 反电势波形THD变化

下载: 全尺寸图片幻灯片

图 9 齿槽转矩变化曲线

下载: 全尺寸图片幻灯片

图 10 永磁钢的涡流损耗变化曲线

下载: 全尺寸图片幻灯片

图 11 空载径向气隙磁密对比

下载: 全尺寸图片幻灯片

图 12 空载反电势对比

下载: 全尺寸图片幻灯片

图 13 齿槽转矩对比

下载: 全尺寸图片幻灯片

参考文献(15)

[1]	刘金辉, 蔡巍.车用内置式永磁驱动电机反电势谐波削弱方法[J].微电机, 2018, 51(6):7-10, 15 doi: 10.3969/j.issn.1001-6848.2018.06.002 Liu J H, Cai W. Method for reducing EMF harmonics of interior permanent magnet synchronous motors for EVs[J]. Micromotors, 2018, 51(6):7-10, 15(in Chinese) doi: 10.3969/j.issn.1001-6848.2018.06.002
[2]	Piña Ortega A J, Paul S, Islam R, et al. Analytical model for predicting effects of manufacturing variations on cogging torque in surface-mounted permanent magnet motors[J]. IEEE Transactions on Industry Applications, 2016, 52(4):3050-3061 doi: 10.1109/TIA.2016.2554102
[3]	Bozorgi A M, Farasat M, Jafarishiadeh S. Model predictive current control of surface-mounted permanent magnet synchronous motor with low torque and current ripple[J]. IET Power Electronics, 2017, 10(10):1120-1128 doi: 10.1049/iet-pel.2016.0850
[4]	张炳义, 蒋鑫, 冯桂宏.磁钢充磁方式对高速永磁电机性能的影响研究[J].机电工程, 2018, 35(7):751-754 doi: 10.3969/j.issn.1001-4551.2018.07.018 Zhang B Y, Jiang X, Feng G H. Effect of magnetic magnetizing method on the performance of high speed permanent magnet motor[J]. Journal of Mechanical & Electrical Engineering, 2018, 35(7):751-754(in Chinese) doi: 10.3969/j.issn.1001-4551.2018.07.018
[5]	陈萍, 唐任远, 佟文明, 等.高功率密度永磁同步电机永磁体涡流损耗分布规律及其影响[J].电工技术学报, 2015, 30(6):1-9 doi: 10.3969/j.issn.1000-6753.2015.06.001 Chen P, Tang R Y, Tong W M, et al. Permanent magnet eddy current loss and its influence of high power density permanent magnet synchronous motor[J]. Transactions of China Electrotechnical Society, 2015, 30(6):1-9(in Chinese) doi: 10.3969/j.issn.1000-6753.2015.06.001
[6]	徐进彬, 张学义, 耿慧慧.永磁轮毂电机内嵌V型磁路结构分析[J].微特电机, 2018, 46(3):32-35 doi: 10.3969/j.issn.1004-7018.2018.03.009 Xu J B, Zhang X Y, Geng H H. Analysis of embedded v-shaped magnetic circuit structure of permanent magnet hub-motor[J]. Small & Special Electrical Machines, 2018, 46(3):32-35(in Chinese) doi: 10.3969/j.issn.1004-7018.2018.03.009
[7]	王晓远, 高鹏.基于进化策略的轮毂电机永磁体结构优化设计[J].中国电机工程学报, 2015, 35(4):979-984 http://d.old.wanfangdata.com.cn/Periodical/zgdjgcxb201504027 Wang X Y, Gao P. Optimal design of permanent magnets of in-wheel motor based on evolution strategy[J]. Proceedings of the CSEE, 2015, 35(4):979-984(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/zgdjgcxb201504027
[8]	Woo D K, Jeong B H. Irreversible demagnetization of permanent magnet in a surface-mounted permanent magnet motor with overhang structure[J]. IEEE Transactions on Magnetics, 2016, 52(4):8102606 http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=edf63ac59ba783d2a8136ac0b66a16f5
[9]	倪有源, 崔征山, 陈俊华, 等.磁极削角表贴式永磁电机解析法建模与分析[J].微特电机, 2018, 46(10):5-9, 14 doi: 10.3969/j.issn.1004-7018.2018.10.002 Ni Y Y, Cui Z S, Chen J H, et al. Modeling and analysis of surface-mounted permanent magnet machines with chamfered magnets[J]. Small & Special Electrical Machines, 2018, 46(10):5-9, 14(in Chinese) doi: 10.3969/j.issn.1004-7018.2018.10.002
[10]	张河山, 邓兆祥, 杨金歌, 等.表贴式永磁电机磁场的解析计算与分析[J].汽车工程, 2018, 40(7):850-857, 864 http://d.old.wanfangdata.com.cn/Periodical/qcgc201807016 Zhang H S, Deng Z X, Yang J G, et al. Analytic calculation and analysis of magnetic field in surface-mounted permanent magnet motor[J]. Automotive Engineering, 2018, 40(7):850-857, 864(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/qcgc201807016
[11]	王芳.表贴式永磁同步电机削极技术的研究[J].船电技术, 2018, 38(2):41-45 doi: 10.3969/j.issn.1003-4862.2018.02.010 Wang F. Research on pole cutting of surface mount permanent magnet synchronous motor[J]. Marine Electric & Electronic Engineering, 2018, 38(2):41-45(in Chinese) doi: 10.3969/j.issn.1003-4862.2018.02.010
[12]	钟添明, 熊万里, 吕浪.永磁同步型机床电主轴齿槽转矩抑制方法研究[J].机械科学与技术, 2014, 33(5):716-722 doi: 10.13433/j.cnki.1003-8728.2014.0519 Zhong T M, Xiong W L, Lü L. A method for suppressing cogging torque in permanent magnet synchronous motor spindle[J]. Mechanical Science and Technology for Aerospace Engineering, 2014, 33(5):716-722(in Chinese) doi: 10.13433/j.cnki.1003-8728.2014.0519
[13]	罗正豪, 井立兵, 高起兴.分段偏心磁极表贴式永磁电机优化设计[J].微特电机, 2018, 46(10):25-27, 37 doi: 10.3969/j.issn.1004-7018.2018.10.006 Luo Z H, Jing L B, Gao Q X. Optimal design of segmented-eccentric magnet pole for SMP synchronous motor[J]. Small & Special Electrical Machines, 2018, 46(10):25-27, 37(in Chinese) doi: 10.3969/j.issn.1004-7018.2018.10.006
[14]	任超, 曹家勇, 梁庆华, 等.磁齿轮啮合型电机齿槽转矩影响因素分析[J].机械科学与技术, 2016, 35(11):1698-1702 doi: 10.13433/j.cnki.1003-8728.2016.1110 Ren C, Cao J Y, Liang Q H, et al. Analysis on cogging torque of a magnetic-geared motor[J]. Mechanical Science and Technology for Aerospace Engineering, 2016, 35(11):1698-1702(in Chinese) doi: 10.13433/j.cnki.1003-8728.2016.1110
[15]	Wu L J, Zhu Z Q, Staton D, et al. Analytical model for predicting magnet loss of surface-mounted permanent magnet machines accounting for slotting effect and load[J]. IEEE Transactions on Magnetics, 2012, 48(1):107-117 doi: 10.1109/TMAG.2011.2165321