Kinematics and Accuracy Analysis of Parallel Bidirectional Deflection Platform
-
摘要: 本文提出一种新型并联驱动双向偏转平台。动平台通过在空间中呈正十字交错且同心的两个分支结构与底座相连接,该平台可以在X、Y两个方向上实现大角度偏转;建立了该平台的运动学方程,得出了Jacobian矩阵;对平台做了运动学仿真分析,对比了仿真结果与理论计算结果,验证了平台设计的可行性与运动的准确性;给出了平台所有的源误差,根据误差独立作用原理对不同类型的源误差分别采用蒙特卡洛法、瞬时臂法和全微分法做了误差分析、计算,得出了各局部误差。按照误差综合方法的均方法对各局部误差做了误差综合,得出了平台分别绕X、Y轴方向上的最大运动误差。
-
关键词:
- 双向偏转平台 /
- Jacobian矩阵 /
- 运动学仿真 /
- 精度分析
Abstract: A new parallel drive bidirectional deflection platform is proposed. The movable platform is connected to the base with the two cross-branched and concentric two-branch structures in the space, and the platform can realize the large-angle deflection in both X and Y directions. The kinematics equation of the platform was established and the Jacobian matrix was obtained. The kinematics simulation analysis of the platform was carried out, and the simulation results and calculation results were compared so as to verify the feasibility of the platform design and the accuracy of the motion. All the source errors of the platform are given. According to the error independent action principle, Monte Carlo method, the instantaneous arm method and the total differential method are used to analyze and calculate the error of different types of source errors respectively. The local errors are obtained. According to the average method of the error synthesis method, the error of each local error is integrated, and the maximum motion error of the platform around the X and Y axes is obtained. -
表 1 平台参数
项目 齿轮 z1 z2 z3 z4 模数 1 1 1 1 齿数 50 160 50 318 精度 7级 7级 7级 7级 表 2 平台位置仿真值与理论计算值
(°) t(s) α β 理论值 仿真值 θ1 θ2 θ1 θ2 1
3
5
7
90.8
3.6
10
18
260.8
3.6
10
18
261.2800
11.5427
32.4835
60.3590
91.15702.5440
22.8960
63.6070
114.4800
165.36001.2814
11.5421
32.4842
60.3581
91.15512.5432
22.8972
63.6090
114.4831
165.3631表 3 平台速度仿真值与理论计算值
(°/s) t(s) α β 理论值 仿真值 θ′1 θ′2 θ′1 θ′2 1
3
5
7
90.8
2.4
4.0
4.0
4.00.8
2.4
4.0
4.0
4.02.5602
7.7254
13.3768
14.5968
16.23585.0880
15.2640
25.4400
25.4400
25.44002.5622
7.7238
13.3778
14.5976
16.23425.0820
15.2720
25.4380
25.4380
25.4380表 4 误差源及性质
轴线 误差名称 误差类型 误差性质 X轴 主动齿轮2制造误差
大驱动拱制造误差
主动齿轮2与电机2轴安装偏心产生的误差
X轴齿轮传动误差制造误差
制造误差
装配误差
制造与装配误差随机误差
随机误差
随机误差
随机误差Y轴 主动齿轮1制造误差
小驱动拱制造误差
主动齿轮1与电机1轴安装偏心产生的误差
Y轴齿轮传动误差
滑伸副配合间隙产生的误差
动平台绕X轴偏转对其绕Y轴偏转的耦合误差制造误差
制造误差
装配误差
制造与装配误差
制造与装配误差
原理误差随机误差
随机误差
随机误差
随机误差
随机误差
系统误差表 5 各齿轮误差参数
齿轮 Fp F′i f′i e1 e2 e3 z1 29 41.699 2 12.699 2 4 10 0 z2 29 67.100 1 18.100 1 4.5 10 5 z3 49 41.699 2 12.699 2 4 10 0 z4 64 79.834 8 15.834 8 4.5 10 5 -
[1] 张彦斌, 荆献领, 韩建海, 等.无耦合二自由度转动并联机构型综合方法研究[J].机械工程学报, 2018, 54(15):21-30 http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201815003Zhang Y B, Jing X L, Han J H, et al. Type synthesis of uncoupled rotational parallel mechanisms with two degrees of freedom[J]. Journal of Mechanical Engineering, 2018, 54(15):21-30(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201815003 [2] Daeinejad F S, Farahmand F, Durali M, et al. Design and analysis of a novel parallel mechanism for prosthetic knee wear test simulators[J]. Journal of Mechanical Science and Technology, 2017, 31(2):885-892 doi: 10.1007/s12206-017-0141-1 [3] Enferadi J, Nikrooz R. The performance indices optimization of a symmetrical Fully spherical parallel mechanism for dimensional synthesis[J]. Journal of Intelligent & Robotic Systems, 2018, 90(3-4):305-321 http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=593c83493d21ad4d603d61bc1ab051dc [4] 王汝贵, 袁吉伟, 孙家兴, 等.一种空间非对称2自由度并联机构设计与应用研究[J].机械设计, 2017, 34(8):85-91 http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jxsj201708015Wang R G, Yuan J W, Sun J X, et al. Design and application of a spatial asymmetric 2-DOF parallel mechanism[J]. Journal of Machine Design, 2017, 34(8):85-91(in Chinese) http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jxsj201708015 [5] 李守忠.两种新颖的柔性机构自由度分析方法[J].机械工程学报, 2016, 52(1):41-46 http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201601005Li S Z. Two Kinds of novel methods for analyzing the degree of freedom of flexure mechanisms[J]. Journal of Mechanical Engineering, 2016, 52(1):41-46(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201601005 [6] Nurahmi L, Schadlbauer J, Caro S, et al. Kinematic analysis of the 3-RPS cube parallel manipulator[J]. Journal of Mechanisms and Robotics, 2015, 7(1):011008 doi: 10.1115/1.4029305 [7] Wang Y, Yu J J, Pei X. Fast forward kinematics algorithm for real-time and high-precision control of the 3-RPS parallel mechanism[J]. Frontiers of Mechanical Engineering, 2018, 13(3):368-375 doi: 10.1007/s11465-018-0519-5 [8] 张军, 谢志江, 吴小勇.基于ADAMS和MATLAB的3-PPR并联机构运动学分析与仿真[J].机床与液压, 2017, 45(17):10-14 doi: 10.3969/j.issn.1001-3881.2017.17.003Zhang J, Xie Z J, Wu X Y. Kinematics analysis and simulation of the 3-PPR parallel mechanism based on ADAMS and MATLAB[J]. Machine Tool & Hydraulics, 2017, 45(17):10-14(in Chinese) doi: 10.3969/j.issn.1001-3881.2017.17.003 [9] 张伟中, 徐灵敏, 童俊华, 等.2-PUR-PSR并联机构的运动学分析及尺度综合[J].机械工程学报, 2018, 54(7):45-53 http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201807006Zhang W Z, Xu L M, Tong J H, et al. Kinematic analysis and dimensional synthesis of 2-PUR-PSR parallel manipulator[J]. Journal of Mechanical Engineering, 2018, 54(7):45-53(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201807006 [10] 王唱, 赵铁石, 赵延治, 等.基于QR分解的少自由度并联机构运动学及刚度分析[J].机械工程学报, 2015, 51(23):28-36 http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201523004Wang C, Zhao T S, Zhao Y Z, et al. Kinematic and stiffness analysis of lower-mobility parallel mechanisms based on QR decomposition[J]. Journal of Mechanical Engineering, 2015, 51(23):28-36(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201523004 [11] 张超, 李彬, 赵新华.一种三自由度并联机构运动学及工作性能分析[J].制造业自动化, 2017, 39(9):54-58 doi: 10.3969/j.issn.1009-0134.2017.09.015Zhang C, Li B, Zhao X H. Kinematics and working performance analysis of a 3-DOF parallel mechanism[J]. Manufacturing Automation, 2017, 39(9):54-58(in Chinese) doi: 10.3969/j.issn.1009-0134.2017.09.015 [12] 柳江, 黎晓伟, 张业, 等.少自由度并联机构馈能悬架运动学特性分析[J].科学技术与工程, 2016, 16(32):132-138 doi: 10.3969/j.issn.1671-1815.2016.32.021Liu J, Li X W, Zhang Y, et al. Kinematics analysis on lower-mobility parallel mechanism for energy-regenerative suspension system[J]. Science Technology and Engineering, 2016, 16(32):132-138(in Chinese) doi: 10.3969/j.issn.1671-1815.2016.32.021 [13] 龚智强, 陈进, 李耀明, 等.振动盘式精密播种机调水平并联机构精度研究[J].农机化研究, 2016, 38(10):56-59, 222 doi: 10.3969/j.issn.1003-188X.2016.10.012Gong Z Q, Chen J, Li Y M, et al. Accuracy research of a vibration tray precision seeder's horizontal adjustment parallel mechanism[J]. Journal of Agricultural Mechanization Research, 2016, 38(10):56-59, 222(in Chinese) doi: 10.3969/j.issn.1003-188X.2016.10.012 [14] 宋轶民, 翟亚普, 孙涛, 等.基于区间分析的一类三转动自由度并联机构的精度设计[J].北京工业大学学报, 2015, 41(11):1620-1626, 1755 doi: 10.11936/bjutxb2015050096Song Y M, Zhai Y P, Sun T, et al. Interval analysis based accuracy design of a 3-DOF rotational parallel mechanism[J]. Journal of Beijing University of Technology, 2015, 41(11):1620-1626, 1755(in Chinese) doi: 10.11936/bjutxb2015050096 [15] 赵永生, 郑魁敬, 李秦川, 等.5-UPS/PRPU 5自由度并联机床运动学分析[J].机械工程学报, 2004, 40(2):12-16 http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jxgcxb200402003Zhao Y S, Zheng K J, Li Q C, et al. Kinematic analysis of 5-UPS/PRPU 5-DOF parallel machine tool[J]. Chinese Journal of Mechanical Engineering, 2004, 40(2):12-16(in Chinese) http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=jxgcxb200402003 [16] 成大先.机械设计手册[M].5版.北京:化学工业出版社, 2008Cheng D X. Mechanical design manual[M]. 5th ed. Beijing:Chemical Industry Press, 2008(in Chinese)