[1]
|
Li X L, Du R, Denkena B, et al. Tool breakage monitoring using motor current signals for machine tools with linear motors[J]. IEEE Transactions on Industrial Electronics, 2005, 52(5):1403-1408 doi: 10.1109/TIE.2005.855656
|
[2]
|
Lin C J, Yau H T, Tian Y C. Identification and compensation of nonlinear friction characteristics and precision control for a linear motor stage[J]. IEEE/ASME Transactions on Mechatronics, 2013, 18(4):1385-1396 doi: 10.1109/TMECH.2012.2202679
|
[3]
|
Jang C, Kim J, Kim Y. Thermal resistance modeling of linear motor driven stages for chip mounter applications[C]//Proceedings of the ITherm 2002. Eighth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems. San Diego, CA, USA: IEEE, 2002: 77-84
|
[4]
|
Kim J J, Jeong Y H, Cho D W. Thermal behavior of a machine tool equipped with linear motors[J]. International Journal of Machine Tools and Manufacture, 2004, 44(7-8):749-758 doi: 10.1016/j.ijmachtools.2004.02.006
|
[5]
|
Eun I U. Comparison between asynchronous and synchronous linear motors as to thermal behavior[J]. International Journal of Precision Engineering and Manufacturing, 2001, 2(3):61-68 http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=JAKO200111920832008
|
[6]
|
Chow J H, Zhong Z W, Lin W, et al. Investigation of thermal effect in permanent magnet linear motor stage[C]//Proceedings of 2010 International Conference on Control Automation Robotics & Vision. Singapore, Singapore: IEEE, 2010: 258-262
|
[7]
|
林献坤, 李燕军, 吴倩倩.高速直线电动机驱动进给轴热行为测试研究[J].制造技术与机床, 2012, (11):25-29 doi: 10.3969/j.issn.1005-2402.2012.11.009Lin X K, Li Y J, Wu Q Q. Test of thermal behavior of high speed feed drive system equipped with linear motor[J]. Manufacturing Technology & Machine Tool, 2012, (11):25-29(in Chinese) doi: 10.3969/j.issn.1005-2402.2012.11.009
|
[8]
|
顾平灿, 徐月同.扁平型永磁直线同步电机热学模型及实验研究[J].组合机床与自动化加工技术, 2015, (11):37-40 http://d.old.wanfangdata.com.cn/Periodical/zhjc201511011Gu P C, Xu Y T. Thermal model and experiment study on a flat permanent-magnet linear synchronous motor[J]. Modular Machine Tool &&utomatic Manufacturing Technique, 2015, (11):37-40(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/zhjc201511011
|
[9]
|
Xu Z Z, Liu X J, Kim H K, et al. Thermal error forecast and performance evaluation for an air-cooling ball screw system[J]. International Journal of Machine Tools and Manufacture, 2011, 51(7-8):605-611 doi: 10.1016/j.ijmachtools.2011.04.001
|
[10]
|
Alejandre I, Artes M. Thermal non-linear behaviour in optical linear encoders[J]. International Journal of Machine Tools and Manufacture, 2006, 46(12-13):1319-1325 doi: 10.1016/j.ijmachtools.2005.10.010
|
[11]
|
Boulesteix A L, Strimmer K. Partial least squares:a versatile tool for the analysis of high-dimensional genomic data[J]. Briefings in Bioinformatics, 2007, 8(1):32-44 doi: 10.1093-bib-bbl016/
|
[12]
|
常英杰, 陆宪忠, 王世龙, 等.基于偏最小二乘回归的发动机排气分析仪线性化研究[J].机械工程学报, 2011, 47(10):76-81 http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201110013Chang Y J, Lu X Z, Wang S L, et al. Study on the linearization of analyzer for engine exhaust based on partial least squares[J]. Journal of Mechanical Engineering, 2011, 47(10):76-81(in Chinese) http://d.old.wanfangdata.com.cn/Periodical/jxgcxb201110013
|
[13]
|
王惠文, 吴载斌, 孟洁.偏最小二乘回归的线性与非线性方法[M].北京:国防工业出版社, 2006Wang H W, Wu Z B, Meng J. Partial least-squares regression:linear and nonlinear methods[M]. Beijing:National Defense Industry Press, 2006(in Chinese)
|
[14]
|
玄光男, 程润伟.遗传算法与工程优化[M].于歆杰, 周根贵, 译.北京: 清华大学出版社, 2004Xuan G N, Cheng R W. Genetic algorithms and engineering optimization[M]. Yu X J, Zhou G G, trans. Beijing: Tsinghua University Press, 2004(in Chinese)
|
[15]
|
Sarabiaa L A, Ortizb M C, Sanchez M S, et al. Partial least squares fine-tuning by a bootstrap estimated signal-noise relation to weight the loadings[J]. Chemometrics and Intelligent Laboratory Systems, 2003, 68(1-2):83-96 doi: 10.1016/S0169-7439(03)00090-X
|