结构试验闭环补偿控制技术初探

赵洪伟; 冯建民

doi:10.13433/j.cnki.1003-8728.2018.0123

结构试验闭环补偿控制技术初探

doi: 10.13433/j.cnki.1003-8728.2018.0123

1.
中国飞机强度研究所全尺寸飞机结构静力/疲劳实验室, 西安 710065

基金项目:

航空科学基金项目（2016ZD23017）与民用飞机专项科研项目（MIZ-2015-F-031）资助

详细信息

作者简介:
赵洪伟(1981-),工程师,硕士,研究方向为飞机结构强度研究及试验控制工作,zhw_zhaohongwei@sina.com

计量
- 文章访问数: 187
- HTML全文浏览量: 34
- PDF下载量: 6
- 被引次数: 0
出版历程
- 收稿日期: 2016-09-19
- 刊出日期: 2018-01-15

A Preliminary Study on Closed-loop Compensation Control for Structural Test

1.
Full Scale Aircraft Structural Static/Fatigue Laboratory, Aircraft Strength Research Institute of China, Xi'an 710065, China

摘要

摘要: 飞机结构强度试验受外界条件作用较明显，试验误差可能发生较大变化。强度试验采用的经典PID控制器，该控制器对误差控制能力有限，难以有效降低试验控制误差。为了解决这个问题，提出一种闭环补偿控制技术。在对控制参数优化技术、PID自适应技术及开环补偿控制技术研究的基础上，深入分析了外界因素对试验的影响机制，设计了一种闭环补偿控制算法，此算法可以根据试验精度的变化控制器输出信号进行实时补偿。补偿控制算法可能导致试验控制系统出现稳定性的问题，所以利用赫尔维茨稳定性判据对该方法的稳定性进行了证明。同时设计了两个结构试验工况对本方法进行物理验证。试验结果表明：本文控制方法对于改善试验控制精度是合理有效的，并在将来有更为广泛的应用价值。
- 飞机结构试验 /
- 控制算法 /
- 闭环补偿 /
- PID
Abstract: Aircraft structural test is affected greatly by the environmental conditions, so that testing control error may be changed largly. The traditional PID controller cannot control testing error effectively. To solve the problem, a closed-loop compensation control technique is developed. Based on the control parameter optimization technique, PID self-adaptive technique and open-loop compensation control scheme, the effect mechanism of environmental conditions was analyzed. A closed-loop compensation control algorithm was designed. Using this control algorithm, the output signal of controller can be compensated in real time to decrease the environmental effect, and the loading system can be controlled precisely. On the other side, the closed-loop compensation control technique may result in system instability, so Hurwitz stability criterion was used to verify the stability of this method. In order to validate the method, two test setups were designed and the verification experiments were perofrmed. The results showed that the present method was effective and reasonable to improve the testing control accuracy, and could be widely used in relevant tests in the future.
- aircraft structure test /
- control algorithm /
- closed-loop compensation /
- PID

HTML全文

参考文献(15)

[1]	刘金甫,张庆媛.飞机结构疲劳试验系统的研制及其发展动向[J].测控技术,1992,26(4):8-11 Liu J F, Zhang Q Y. Development of the aircraft structural fatigue test systems and its trends[J]. Measurement & Control Technology, 1992,12(4):8-11(in Chinese)
[2]	Eenkhoorn N C. Development of a virtual testing methodology for structural fatigue testing setups[D]. Delft, the Netherlands:Delft University of Technology, 2010
[3]	彭安华,孙旭东,王智明.基于正交试验法的PID控制器参数整定[J].机械科学与技术,2011,30(6):1028-1032 Peng A H, Sun X D, Wang Z M. Parameter tuning for PID controllers based on orthogonal experiment[J]. Mechanical Science and Technology for Aerospace Engineering, 2011,30(6):1028-1032(in Chinese)
[4]	常俊林,李亚朋,马小平,等.基于改进差分进化算法的PID优化设计[J].控制工程,2010,17(6):807-810 Chang J L, Li Y P, Ma X P, et al. Optimization design for PID controller based on an improved differential evolution algorithm[J]. Control Engineering of China, 2010,17(6):807-810(in Chinese)
[5]	洪博,董泽.PID参数优化方法对优化效果的影响研究[J].计算机仿真,2015,32(2):391-394 Hong B, Dong Z. Study of an effect of PID parameter optimization methods on optimization[J]. Computer Simulation, 2015,32(2):391-394(in Chinese)
[6]	张鹤琼.基于动态模糊微分模型的PID优化算法[J].科技通报,2013,29(4):100-102 Zhang H Q. PID optimization algorithm based on the dynamic fuzzy differential model[J]. Bulletin of Science and Technology, 2013,29(4):100-102(in Chinese)
[7]	刘慧博,王静,吴彦合.无刷直流电机模糊自适应PID控制研究与仿真[J].控制工程,2014,21(4):583-587 Liu H B, Wang J, Wu Y H. Study and simulation of fuzzy adaptive PID control of brushless DC motor[J]. Control Engineering of China, 2014,21(4):583-587(in Chinese)
[8]	闫秀英,任庆昌,孟庆龙.一种自校正PID控制器设计与仿真研究[J].系统仿真学报,2006,18(S2):753-756 Yan X Y, Ren Q C, Meng Q L. Design and simulation for self-tuning PID controller[J]. Journal of System Simulation, 2006,18(S2):753-756(in Chinese)
[9]	王述彦,师宁,冯忠绪.基于模糊PID控制器的控制方法研究[J].机械科学与技术,2011,30(1):166-172 Wang S Y, Shi N, Feng Z X. A method for controlling a loading system based on a fuzzy PID controller[J]. Mechanical Science and Technology for Aerospace Engineering, 2011,30(1):166-172(in Chinese)
[10]	龙运栋,段小刚,李涵雄.基于时空分离AFM微悬臂的模糊PID控制研究[J].控制工程,2013,20(3):456-459,465 Long Y D, Duan X G, Li H X. Fuzzy PID control of micro-cantilever in AFM based on separation of time-spatial[J]. Control Engineering of China, 2013,20(3):456-459,465(in Chinese)
[11]	姚烯,刘春生,王晓霞.基于去伪控制的PID自适应参数调节[J].电光与控制,2014,21(5):29-33 Yao X, Liu C S, Wang X X. Automatic PID parameter tuning based on unfalsified control[J]. Electronics Optics & Control, 2014,21(5):29-33(in Chinese)
[12]	Burnett G, Patterson A, Powlesland I, et al. An application of parallel processing to distributed real time control of aircraft testing[C]//Proceedings of the Third IEEE Conference on Control Applications, August 24-26, 1994, Glasgow. Glasgow:IEEE, 1994,2:817-824
[13]	Urnetit G, Dutton S, Hartley D, et al. Advanced control techniques for full scale fatigue testing[C]//ICAF 2005. Hamburg, 2005:23-28
[14]	白传栋,王德义.交流位置伺服系统非线性摩擦补偿控制研究[J].太原理工大学学报,2015,46(4):430-434,439 Bai C D, Wang D Y. Research on nonlinear friction compensation control for AC servo system[J]. Journal of Taiyuan University of Technology, 2015,46(4):430-434,439(in Chinese)
[15]	胡寿松.自动控制原理[M].5版.北京:科学出版社,2007 Hu S S. Automatic control theory[M]. 5th ed. Beijing:Science Press, 2007(in Chinese)