Analysis on Hydrodynamic Lubrication Performance of Micro-texture on Hydraulic Cylinder Piston Surface
-
摘要: 以织构化间隙密封液压缸为研究背景,利用平均雷诺方程对缸筒与活塞的配合处微织构流场进行数学建模,采用有限差分法对平均雷诺方程进行离散,分别对织构形貌为球缺面、圆柱面、圆锥面、抛物面、六面体和正方体进行数值模拟,获得最优微织构形貌,同时探讨了表面粗糙度,表面方向参数和面积占有率对表面摩擦因数的影响。结果表明:六种不同形貌的微织构均能在活塞表面产生动压润滑效果,圆柱形微织构表面动压润滑性能最好;粗糙表面的粗糙峰在运动过程中能够形成动压承载力,圆柱形表面的摩擦因数随粗糙度的增加而增加,微织构的摩擦因数随表面方向参数的增加而减小,随着面积占有率的增加而减小。
-
关键词:
- 液压缸 /
- 微织构 /
- 平均Reynolds方程 /
- 粗糙度
Abstract: The paper was on the background of the textured cylinder clearance seal. The average Reynolds equation was used in the micro-texture flow field for mathematical modeling. The finite difference method was used to discrete the average Reynolds equation. There are six morphologies such as hemispherical surface, cylinder, paraboloid, six-sided cube and micro-textured simulated for getting optimal micro-textured appearance. The effects of the surface roughness, surface orientation parameters and area occupancy rate on the surface friction coefficient are explored. The results show that six different morphologies can produce hydrodynamic lubrication on the surface of the piston. The hydrodynamic lubrication performance of the cylinder is the best. The rough surface asperities can form dynamic pressure bearing force during exercise. The cylindrical surface friction coefficient increases with the roughness. The micro-texture coefficient of friction decreases with the increase of surface direction parameters, area occupancy rate.-
Key words:
- hydraulic cylinder /
- micro-texture /
- average Reynolds equation /
- roughness
-
[1] 马晨波,朱华,历建全.摩擦副不同表面织构化的润滑减摩性能试验研究[J].中国矿业大学学报,2010,39(2):244-248 Ma C B, Zhu H, LI J Q. Experimental study of tribological properties of texture on different surfaces of frictional pairs[J]. Journal of China University of Mining & Technology, 2010,39(2):244-248(in Chinese) [2] 谢志斌,于爱兵,陈斌,等.高速钢仿生表面的摩擦磨损特性[J].兵器材料科学与工程,2015,38(1):33-35 Xie Z B, Yu A B, Chen B, et al. Friction and wear behavior of bionic surface on high speed steel[J]. Ordnance Material Science and Engineering, 2015,38(1):33-35(in Chinese) [3] 符永宏,张华伟,纪敬虎,等.微造型活塞环表面的润滑性能数值分析[J].内燃机学报,2009,27(2):180-185 Fu Y H, Zhang H W, Ji J H, et al. Numerical analysis on the lubrication performance of piston ring by surface micro-texturing[J]. Transactions of CSICE, 2009,27(2):180-185(in Chinese) [4] Kai M, Tsuboi R, Sasaki S. A study on in-situ observation of the micro flow of lubricant on the textured surface[J]. Procedia Engineering, 2013,68:12-18 [5] Syed I, Sarangi M. Hydrodynamic lubrication with deterministic micro textures considering fluid inertia effect[J]. Tribology International, 2014,69:30-38 [6] 赵文杰,王立平,薛群基.织构化提高表面摩擦学性能的研究进展[J].摩擦学学报,2011,31(6):622-631 Zhao W J, Wang L P, Xue Q J. Development and research progress of surface texturing on improving tribological performance of surface[J]. Tribology, 2011,31(6):622-631(in Chinese) [7] Wang X L, Kato K, Adachi K, et al. Loads carrying capacity map for the surface texture design of SiC thrust bearing sliding in water[J]. Tribology International, 2003,36(3):189-197 [8] Ogihara H, Kido T, Yamada H, et al. Technology for reducing engine rubbing resistance by means of surface improvement[J]. Honda R&D Technical Review, 2000,12(2):93-98 [9] 尹必峰,钱晏强,汪博文,等.柴油机缸套表面织构协同润滑效应[J].内燃机学报,2014,32(2):178-185 Yin B F, Qian Y Q, Wang B W, et al. Combined lubrication effectiveness of surface textures on diesel cylinder liners[J]. Transactions of CSICE, 2014,32(2):178-185(in Chinese) [10] 李凯凯,于海武,王静秋,等.混合织构发动机缸套的减摩试验研究[J].内燃机工程,2014,35(5):113-118 Li K K, Yu H W, Wang J Q, et al. Experiment investigation on friction reduction of mixed texture cylinder liner[J]. Chinese Internal Combustion Engine Engineering, 2014,35(5):113-118(in Chinese) [11] Ranjan R, Lambeth D N, Tromel M, et al. Laser texturing for low-flying-height media[J]. Journal of Applied Physics, 1991,69(8):5745-5747 [12] 梁瑛娜,高殿荣,毋少峰.凹坑形仿生非光滑表面滑靴副的动压润滑计算[J].机械工程学报,2015,51(24):153-160 Liang Y N, Gao D R, Wu S F. Hydrodynamic lubrication calculation for slipper/swash plate pair with bionic non-smooth concave surface[J]. Journal of Mechanical Engineering, 2015,51(24):153-160(in Chinese) [13] Patir N, Cheng H S. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication[J]. Journal of Lubrication Technology, 1978,100(1):12-17 [14] Rohde S M, Whitaker K W, Mcallister G T. A study of the effects of piston ring and engine design variables on piston ring friction[M]//Rohde S M, Wilcock D F, Cheng H S. Energy Conservation Through Fluid Film Lubrication Technology:Frontiers in Research and Design. New York:ASME, 1979:432-452 [15] Greenwood J A, Tripp J H. The contact of two nominally flat rough surfaces[J]. Proceedings of the Institution of Mechanical Engineers, 1970,185(1):625-633
点击查看大图
计量
- 文章访问数: 197
- HTML全文浏览量: 24
- PDF下载量: 7
- 被引次数: 0