滚珠式操纵软轴中滚珠接触应力分析

陈开颜; 宋笔锋; 喻天翔; 张玉刚

doi:10.13433/j.cnki.1003-8728.2016.0202

滚珠式操纵软轴中滚珠接触应力分析

doi: 10.13433/j.cnki.1003-8728.2016.0202

1.
西北工业大学航空学院, 西安 710072

基金项目:

国家自然科学基金项目(51105308)与中央高校基本科研业务费专项资金项目(310201401JCQ008)资助

详细信息

作者简介:
陈开颜(1991-),硕士研究生,研究方向为飞行器设计,机构系统仿真及耐久性分析,chenkaiyan_kevin@foxmail.com

通讯作者:
宋笔锋,教授,博士生导师,bfsong@nwpu.edu.cn

计量
- 文章访问数: 110
- HTML全文浏览量: 26
- PDF下载量: 6
- 被引次数: 0
出版历程
- 收稿日期: 2014-04-23
- 刊出日期: 2016-02-05

Study on Contact Stress of Balls in Flexball

1.
School of Aeronautics, Northwestern Polytechnical University, Xi'an 710072, China

摘要

摘要: 针对芯部滑杆与滚珠之间的多接触问题,基于冲击函数法,应用ADAMS软件进行动力学仿真分析,获得各芯部滑杆与滚珠之间的接触力。选取芯部滑杆受拉时,受接触力最大的dw8号滚珠作为研究对象,在ABAQUS环境下建立接触模型,求解接触应力参数。主要结论如下:1)推拉芯部滑杆时,芯部滑杆上下表面受交变接触应力,且最大应力幅值比滚珠大,使其较滚珠更易出现接触疲劳; 2) Mises等效应力由芯部滑杆内部向外先增大后减小,而最大值出现在接触面以下一定距离,故疲劳裂纹多由芯部滑杆内部产生,而逐渐向其表面扩展。
- 滚珠式操纵软轴 /
- 动力学仿真 /
- 接触应力 /
- 接触疲劳
Abstract: In order to acquire the contact force between balls and central rail, the ADAMS software was utilized to perform the dynamic simulation for the multi-contact problem of central rail and balls based on impact function method. The dw8 ball which experienced the maximum contact force was chosen as the research model for the case that the central rail was subjected to tension. Contact stress parameters were obtained with a contact model established in ABAQUS software. It can be concluded that:1) When a central rail is being pushed or pulled, the alternative contact stress will exist on both upper and lower surfaces of the central rail and the stress amplitude is larger than that on the ball, which makes the surface of central rails be prone to contact fatigue damage; 2) The amplitude of Von Mises stress is firstly increased and then decreased from the inner to the outer, and the maximum amplitude occurrs slightly below the contact surface, which explains the reason why the fatigue cracks usually forms inside of the contact body and slowly extends to the surface. The simulation test and conclusions provide useful results for future study of the durability design of flexballs.
- abaqus /
- contact stress /
- dynamics simulation /
- fatigue damage

HTML全文

参考文献(12)

[1]	徐要.滚珠式操纵软轴技术研究[J].江苏航空,2010,(3):13-15 Xu Y. Research on techniques of ball flexible control cable[J]. Jiangsu Aviation, 2010,(3):13-15(in Chinese)
[2]	邓四二,谢鹏飞,杨海生,等.高速角接触球轴承保持架柔体动力学分析[J].兵工学报,2011,32(5):625-631 Deng S R, Xie P F, Yang H S, et al. Flexible-body dynamics analysis on cage of high-speed angular contact ball bearing[J]. Acta Armamentarii, 2011,32(5):625-631(in Chinese)
[3]	Nataraj C, Harsha S P. The effect of bearing cage run-out on the nonlinear dynamics of a rotating shaft[J]. Communications in Nonlinear Science and Numerical Simulation, 2008,13(4):822-838
[4]	Mei X S, Tsutsumi M, Tao T, et al. Study on the load distribution of ball screws with errors[J]. Mechanism and Machine Theory, 2003,38(11):1257-1269
[5]	王福吉,阳江源,贾振元,等.滚珠丝杠副非协调性接触特性研究[J].中国机械工程,2011,22(19):2293-2297 Wang F J, Yang J Y, Jia Z Y, et al. Study on Non-conformal contact characteristics of ball screw[J]. China Mechanical Engineering, 2011,22(19):2293-2297(in Chinese)
[6]	单小彪.钢丝滚道球轴承的接触力学特性及其相关技术研究[D].哈尔滨:哈尔滨工业大学,2008 Shan X B. Research on the contact mechanics characteristics and relative aspects of a wire race ball bearing[D]. Harbin:Harbin Institute of Technology, 2008(in Chinese)
[7]	李增刚.ADAMS入门详解与实例[M].北京:国防工业出版社,2006 Li Z G. ADAMS explanation introduction and examples[M]. Beijing:National Defense Industry Press, 2006(in Chinese)
[8]	蒋鹏.双层滚动轴承运动学研究[D].南京:南京航空航天大学,2011 Jiang P. Research on motion-characteristics of Double decker rolling-element bearing[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2011(in Chinese)
[9]	朱利军,谭晶,黄迪山,等.基于ADAMS的深沟球轴承仿真分析[J].轴承,2011,(2):3-6 Zhu L J, Tan J, Huang D S, et al. Simulation analysis of deep groove ball bearings based on ADAMS[J]. Bearing, 2011,(2):3-6(in Chinese)
[10]	傅友宾.基于PRO/E和ADAMS的变速器动力学仿真[D].大连:大连理工大学,2007 Fu Y B. Investigation on dynamics simulation of transmission based on PRO/E and ADAMS[D]. Dalian:Dalian University of Technology, 2007(in Chinese)
[11]	刘泽九,贺士荃,刘晖.滚动轴承应用[M].北京:机械工业出版社,2007 Liu Z J, He S Q, Liu H. Rolling bearing analysis[M]. Beijing:China Machine Press, 2007(in Chinese)
[12]	Harris T A,Korzalas M N.滚动轴承分析(第1卷)轴承技术的基本概念[M].5版.罗继伟,马伟,译.北京:机械工业出版社,2010 Harris T A, Korzalas M N. Essential concepts of bearing technology (Ⅰ)[M]. 5 edition. Luo J W, Ma W, trans. Beijing:China Machine Press, 2010(in Chinese)