Simulating Flow and Heat Transfer in Lubrication System of a Heavy-duty Automobile Transmission
-
摘要: 应用AMESim软件并结合AMESet二次开发平台,建立了某重型汽车变速器润滑系统流动与传热耦合仿真模型,并在变速器专用试验台上进行了模型的实验验证。应用所建模型完成了不同工况条件下润滑系统的流动与传热仿真,对典型润滑节点的润滑状况进行了分析评价及改进。结果表明:变速器在低速大负荷及高速小负荷工况下工作时,除中间轴左轴承润滑不足外,其余轴承均润滑良好;采取加大轴承润滑油道直径使节点流量率增大来改善中间轴左轴承润滑状况的措施是可行的。Abstract: The model for simulating the flow and heat transfer in the lubrication system of a heavy-duty automobile transmission was established with AMESim and AMESet and validated on the test bed designed for the automobile transmission. The flow and heat transfer in the lubrication system under different operation conditions were simulated, and the lubrication conditions at several typical nodes were analyzed and improved. The simulation results and their analysis show that all the validated bearings have good lubrication except the left bearing of the middle axle of the heavy-duty automobile transmission under the operation conditions of high speed and light load or low speed and heavy load. It is feasible to increase the oil channel diameter so that the node flow rate increases in order to improve the lubrication of the left bearing of the middle axle.
-
Key words:
- automebile transmissions /
- computer simulation /
- computer software /
- design /
- flow
-
[1] 许翔,毕小平.车用传动装置润滑系统的流动仿真[J].润滑与密封,2006,174(2):17-19 Xu X, Bi X P. Simulation of lubricant flow in lubricating system of vehicle gearing[J]. Lubrication Engineering,2006,174(2):17-19 (in Chinese) [2] Michlin Y, Myunster V. Determination of power losses in gear transmissions with rolling and sliding friction incorporated[J]. Mechanism and Machine Theory,2002,37(2):167-174 [3] Changenet C,Velex P. Housing influences on churning losses in geared transmissions[J]. Journal of Mechanical Design, Transactions of the ASME,2008,130(6) [4] Al-Shibl K, Simmons K, Eastwick C N. Modeling windage power loss from an enclosed spur gears[J]. Journal of Power and Energy,2007,221(3):331-341 [5] Seetharaman S, Kahraman A, Moorhead M D, et al. Oil churning power losses of a gear pair: experiments and model validation[J]. Journal of Tribology,2009,131(2):1-10 [6] Heingartner P, Mba D. Determining power losses in the helical gear mesh: case study[C]// Proceeding of Design Engineering Technical Conferences and Computers and Information in Engineering Conference,2003 [7] Anderson N E, Loewenthal S H. Efficiency of nonstandard and high contact ratio involutes spur gears[J]. Journal of Mechanisms, Transmissions, and Automation in Design,1986,108(1):119-126 [8] Xu H, Kahraman A, Anderson N E, et al. Prediction of mechanical efficiency of parallel-axis gear pairs[J]. Journal of Mechanical Design, Transactions of the ASME,2007,129(1):58-68 [9] 吴昌林,余联庆,方晓初.汽车变速箱的热网络分析[J].华中理工大学学报,1998,26(4):63-66 Wu C L, Yu L Q, Fang X C. A thermal network analysis of the automobile gearbox[J]. Journal of Huazhong University of Science and Technology,1998,26(4):63-66 (in Chinese) [10] Seetharman S, Kahraman A. Load-independent spin power losses of a spur gear pair:model formulation[J]. Journal of Tribology,2009,131(2):1-11 [11] Changenet C, Velex P. A model for the prediction of churning losses in geared transmissions-preliminary results[J]. Journal of Mechanical Design, Transactions of the ASME,2007,129(1): 128-133 [12] 阮登芳,刘波,陈志约,等.重型汽车变速器润滑系统热平衡仿真与实验[J].中国机械工程,2011,22(10):1242-1246 Ruan D F, Liu B, Chen Z Y, et al. Simulation and experiment on heat blance process in lubrication system of a heavy-duty automobile transmission[J]. China Mechanical Engineering,2011,22(10):1242-1246 (in Chinese) [13] 胡邦喜.设备润滑基础[M].北京:冶金工业出版社,2002 Hu B X. Basic principle of lubrication for equipments[M]. Beijing:Metallurgy Industry Press,2002 (in Chinese)
点击查看大图
计量
- 文章访问数: 159
- HTML全文浏览量: 36
- PDF下载量: 10
- 被引次数: 0