Analysis on Thermal Properties of Grease-lubricated Ball Bearing
-
摘要: 针对球轴承高速运转时的热生成及热边界条件问题,建立轴承拟静力学模型分析其受力状态,根据Palmgren经验公式计算轴承摩擦产热,并应用传热学理论,建立考虑热阻抗影响的脂润滑轴承热传递网络模型;研制轴承-转子系统,测量不同工况条件下的轴承外圈温度,试验结果表明:理论模型能准确预测脂润滑球轴承运转时的温升状况,误差在10%以内;轴承启动时其温度上升速度最快,轴承转速和预紧力对其最终稳态温度影响较大,需要加以合理控制。Abstract: Considered the heat generation and thermal boundary condition of the rotating ball bearing, a quasi-staticmodel of ball bearing was established to analyze the stress state of the bearing, and the frictional heat of the bearingwas calculated by the Palmgren empirical formula. Based on heat transfer theory, a heat transfer network model,which took the thermal resistances into account, was constructed for grease-lubricated bearing. A bearing-rotorsystem was developed to measure the temperature changes of bearing outer ring in various working conditions. Theexperimental results indicate that the proposed models can effectively predict the temperature rises of rotatinggrease-lubricated ball bearings and the prediction error is less than 10%; the temperature rises quickest in setupphase of bearings; and the rotating speed and preload of bearings must require reasonable control, which have a biginfluence on the steady temperature.
-
Key words:
- ball bearings /
- boundary conditions /
- calculations
-
[1] Chinese) [2] Paraschiv D,Nagit G,Sarbu I,et al.Measurement of the bottoming voltage in the ball-bearings race [J].Metalurgia International,2009,15(10): 107-113 [3] Jedrzejewski J,Kowal Z.High-speed precise machine tools spindle units improving[J]. Journal of Materials Processing Technology,2005,162-163: 615-621 [4] 刘颖慧,刘树林,唐友福,等.基于斜率关联度的模式识别方法及滚动轴承故障诊断应用[J]. 机械科学与技术,2012,31 (9): 1500-1503Liu Y H,Liu S L,Tang Y F,et al.A method of pattern recognition with slope relational degree and its application to rolling bearing fault diagnosis [J].Mechanical Science and Technology for Aerospace Engineering,2012,31 (9): 1500-1503 (in Chinese) [5] 张成铁,陈国定,李建华.高速滚动轴承的动力学分析[J]. 机械科学与技术,1997,16(1): 136-139Zhang C T,Cheng G D,Li J H.Dynamic analysis of high-speed roller bearings[J]. Mechanical Science and Technology for Aerospace Engineering,1997,16 (1): 136-139 (in Chinese) [6] 刘志全,张鹏顺,沈允文.高速圆柱滚子轴承的热分析模型[J]. 机械科学与技术,1997,16(4): 607-611Liu Z Q,Zhang P S,Shen Y W.Thermal analysis model of high speed cyclinderical roller bearing[J].Mechanical Science and Technology for Aerospace Engineering,1997,16(4): 607-611 (in Chinese) [7] Lin C W,Tu J F,Kamman J.An integrated thermomechanical-dynamic model to characterize motorized machine tool spindles during very high speed rotation[J].International Journal of Machine Tools & Manufacture,2003,43(10): 1035-1050 [8] Zahedi A,Movahhedy M r.Thermo-mechanical modeling of high speed spindles [J]. Scientia Iranica,2012,19(2): 282-293 [9] Pouly F,Changenet C,Ville F,et al.Investigations on the power losses and thermal behaviour of rolling element bearings [J]. Proceedings of the Institution of Mechanical Engineers,Part J: Journal of Engineering Tribology,2010,224(9): 925-993 [10] 徐跃进.高速脂润滑轴承温升失效分析与试验研究[J].机械设计,2008,25(4): 49-51Xu Y J.Temperature rise failure analysis and test research on the high speed grease-lubricated bearing[J].Journal of Mechanical Design,2008,25 (4): 49-51 (in [11] 李秀娟,王黎钦,古乐,等.高速陶瓷球轴承脂润滑试验研究[J]. 润滑与密封,2002,(3): 20-22Li X J,Wang L Q,Gu L,et al.Experiment on grease lubricated high-speed hybrid ceramic bearing [J].Lubrication Engineering,2002,(3): 20-22 (in Chinese) [12] Holkfp T,Cao H,Kolr P,et al.Thermo-mechanical model of spindles [J]. CIrP Annals-Manufacturing Technology,2010,59(1): 365-368 [13] 李泽强,潘奔流,王健,等.高速电主轴用脂润滑轴承性能试验[J]. 轴承,2011,(6): 29-32Li Z Q,Pan B L,Wang J,et al.Performance test of grease-lubricated bearing for high-speed electric spindle[J].Bearing,2011,(6): 29-32 (in Chinese) [14] 胡志刚,徐诚,王永娟.有限元-迭代法在电主轴轴系转子动静特性分析中的应用[J]. 机械科学与技术,2003,22(6): 917-919,922Hu Z G,Xu C,Wang Y J.A finite-element iterative method for analysis of static-dynamic characterisitic of shaft rotor in motorized spindle[J]. Mechanical Science and Technology for Aerospace Engineering,2003,22(6): 917-919,922 (in Chinese) [15] Palmgren A.Ball and roller bearing engineering[M].4th Edition,Burkbank,Philadelphia,1959[15] Jorgenson B r,Shin Y C.Dynamics of machine tool spindle/bearing systems under thermal growth [J].American Society of Mechanical Engineers,Dynamic Systems and Control Division,1996,58: 333-340 [16] Chen X A,Liu J F,He Y,et al.A thermal analyzing model for high speed motorized spindles-thermal properties[J]. Advanced Science Letters,2012,9 (1):767-772
点击查看大图
计量
- 文章访问数: 153
- HTML全文浏览量: 34
- PDF下载量: 14
- 被引次数: 0