陶瓷CBN砂轮磨削镍基铸造高温合金K418磨削力研究

杨长勇; 徐九华; 顾珅珅; 丁文锋; 傅玉灿

doi:10.13433/j.cnki.1003-8728.2014.0507

陶瓷CBN砂轮磨削镍基铸造高温合金K418磨削力研究

doi: 10.13433/j.cnki.1003-8728.2014.0507

1.
南京航空航天大学机电学院, 南京 210016

基金项目:

国家自然科学基金项目(51235004,51305200)

江苏省自然科学基金项目(BK20130805)

江苏省科技支撑项目(BE2013122)资助

详细信息

作者简介:
杨长勇(1980-)，讲师术，博士，研究方向为高性能磨削技yangchy@nuaa.edu.cn

计量
- 文章访问数: 142
- HTML全文浏览量: 23
- PDF下载量: 7
- 被引次数: 0
出版历程
- 收稿日期: 2013-02-20
- 刊出日期: 2015-06-10

Investigation on the Grinding Force of the Casted Nickel-based Superalloy K418 with a Vitrified CBN Wheel

1.
College of Mechanical and Electrical Engineering Nanjing University of Aeronautics and Astronautics, Nanjing 210016

摘要

摘要: 系统开展了陶瓷结合剂CBN砂轮磨削K418的试验研究,测试了不同砂轮线速度、工件进给速度及切深条件下的磨削力。通过对试验数据的分析处理,得到上述3个工艺参数对磨削力、力比及磨削比能的影响规律。并拟合出了陶瓷结合剂CBN砂轮磨削基铸造高温合金K418时磨削力的经验公式,该公式估算误差低于10%。磨削力和力比均随着工件进给速度、切深和当量磨削厚度的增大而增大,随砂轮线速度的减小而增大。随着当量磨削厚度的不断增加,磨削比能呈下降趋势。
- 镍基铸造高温合金K418 /
- 磨削力 /
- 陶瓷结合剂CBN砂轮 /
- 经验公式
Abstract: The grinding experiments are carried out by using the vitrified cubic boron nitride(CBN) wheels on the casted nickel-based superalloy K418. The grinding forces are measured on the various process parameters, including the wheel speed,workpiece speed and depth of cut,and the influencing law of process parameters on the grinding force,force ratio and specific energy are studied in details. The grinding force and force ratio increase with the increasing of workpiece speed,depth of cut and equivalent grinding chip thickness,and with the decreasing of wheel speed. The specific energy decreases with the increasing of equivalent grinding chip thickness. The experience formula of the grinding force with a vitrified CBN wheels is obtained and the relative error is less than 10%.
- cast nickel-based superalloy K418 /
- experiements /
- experience formula /
- grinding force

HTML全文

参考文献(11)

[1]	郭建亭．高温合金材料学[M]．北京:科学出版社，2010 Guo J T. Materials science and engineering for superalloys[M]. Beijing:Science Press，2010 (in Chinese)
[2]	Chen M，Li X T，Sun F H，et al. Studies on the grinding characteristics of directionally solidified nickel-based superalloy[J]. Journal of Materials Processing Technology，2001，116:165-169
[3]	任敬心，康仁科，史兴宽．难加工材料的磨削[M].北京:国防工业出版社，1999 Ren J X，Kang R K，Shi X K. Grinding of difficut-to- cut materials[M]. Beijing: National Defense Industry Press，1999 (in Chinese)
[4]	苏若斌，陈国定，王涛．GH4169 高温合金平面磨削力研究[J]．机械科学与技术，2012，31(5): 818-821 Su R B，Chen G D，Wang T. Study on the surface grinding force of superalloy GH4169[J]. Mechanical Science and Technology for Aerospace Engineering，2012，31(5): 818-821 (in Chinese)
[5]	Yang C Y，Xu J H，Ding W F，et al. Dimension accuracy and surface integrity of creep feed ground titanium alloy with monolayer brazed cbn shaped wheels[J].Chinese Journal of Aeronautics，2010，23(5): 585-590
[6]	Shi Z，Malkin S. Wear of electroplated CBN grinding wheels[J]. Transactions of the ASME，2006，128:110-118
[7]	Ding W F，Xu J H，Chen Z Z，et al. Wear behavior and mechanism of single-layer brazed CBN abrasive wheels during creep-feed grinding cast nickel-based superalloy[J].International Journal of Advanced Manufacturing Technology，2010，51(5-8): 541-550
[8]	刘高群．铸造镍基高温合金K418切削性能试验研究[D].南京: 南京理工大学，2006 Liu G Q. Research on cutting property experiment of casting nickel base superalloy K418[D]. Nanjing: Nanjing University of Science and Technology，2006 (in Chinese)
[9]	Werner G. Influence of work material on grinding forces[J].Annals of the CIRP，1978，27(1): 243-248
[10]	Ren Y H，Zhang B，Zhou Z X. Specific energy in grinding of tungsten carbides of various grain sizes[J]．CIRP Annals-Manufacturing Technology，2009，58(1): 299-302
[11]	Backer W R，Marshall E R，Shaw M C. The size effect in metal cutting[J]. Transactions of the ASME，1974，10(1): 61-71