回转曲面直纹面槽数控加工技术研究

蔺小军; 李政辉; 高春; 李宜明

回转曲面直纹面槽数控加工技术研究

1.
西北工业大学现代设计与集成制造技术教育部重点实验室,西安 710072

基金项目:

“十一五”国家科技支撑计划重点项目(2008BAF32B10)资助

详细信息

作者简介:
蔺小军(1968-)，高级工程师，博士，研究方向为精密测量,CAD/CAM,linxj@nwpu.edu.cn

计量
- 文章访问数: 131
- HTML全文浏览量: 24
- PDF下载量: 4
- 被引次数: 0
出版历程
- 收稿日期: 2011-12-21
- 刊出日期: 2015-06-10

Study on NC Machining of Ruled Surfaces Slot with Surface of Revolution

1.
The Key Laboratory of Contemporary Design and Integrated Manufacturing Technology, Ministry of Education,Northwestern Polytechnical University,Xi'an 710072

摘要

摘要: 针对回转曲面直纹面槽类零件的数控加工问题对其五轴数控编程进行研究。粗加工采用直纹面驱动方法计算加工刀轴矢量和刀位点,对计算方法进行了研究。精加工采用两点偏置法修正刀轴矢量用以减少柱刀侧铣非可展直纹面产生的原理性误差;并且提出了一种刀位点修正算法,解决了平底刀加工曲面时所产生的过切问题。实例验证表明该算法大大减小了柱刀侧铣非可展直纹面产生的原理性误差,有效的提高了加工精度与表面质量,并且使用可靠。
- 回转曲面直纹面槽 /
- 直纹面 /
- 侧铣 /
- 五轴加工
Abstract: A new approach was presented for the five-axis NC machining of the ruled surfaces slot with surface of revolution part.The cutter axis orientation and the cutter location point were identified though the ruled surface driving method in rough machining,and the calculation method was researched.The double points offset method was used to modify the error caused by flanking milling intractable ruled surface by cylindrical cutter.A cutter location point correction algorithm was presented to solve the problem of overcut in flat-end tool machining.Experimental results demonstrate that the proposed method not only solves the problem of machining principle error in flanking milling intractable ruled surface by cylindrical cutter,but also improves machined surface quality and reduces surface roughness and improves the quality of test piece reliably.
- ruled surface slot with surface of revolution /
- ruled surface /
- flank milling /
- five-axis NC machining

HTML全文

参考文献(15)

[1]	Liu X W. Five-axis NC cylindrical milling of sculptured surfaces[J].Computer-Aided Design,1995,27(12):887-894
[2]	Lee Y S,Bahattin K. Ellipse-offset approach and inclined zig-zagmethod for multi-axis roughing of ruled surface pockets[J].Computer-Aided Design,1998,30(12):957-971
[3]	Tsay D M,Her M J. Accurate 5-axis machining of twisted sur-faces[J].Journal of Manufacturing Science and Engineer-ing,2001,123:731-738
[4]	赖天琴,李峰,孔德治. 计算机辅助加工直纹面的新方法[J].西安交通大学学报,1996,30(2):61-67
[5]	于源,赖大琴,员敏. 基于特征的直纹面5轴侧铣精加工刀位计算方法[J].机械工程学报,2002,38(6):130-133
[6]	Redonnet J M,Rubio W,Dessein G. Side milling of ruled sur-faces,positioning of the milling cutter and calculation of interfer-ence[J].International Journal for Advanced ManufacturingTechnology,1998,14:459-465
[7]	Sanjeev B,Stephen M,Cornelia M. Flank milling with flat endcutter[J].Computer-Aided Design,2003,35:293-300
[8]	Cornelia M,Sanjeev B,Stephen M. Triple tangent flank millingof ruled surfaces[J].Computer-Aided Design,2004,36:375-378
[9]	蔡永林,席光,赉建中. 任意扭曲直纹面叶轮数控侧铣刀位计算与误差分析[J].西安交通大学学报,2004,38(5):517-520
[10]	宫虎,曹利新,刘健. 数控侧铣加工非可展直纹面的刀位整体优化原理与方法[J].机械工程学报,2005,41(11):134-139
[11]	Li C G,Bedi S,Mann S. Surface design for flank milling[J].Submitted to Computer-Aided Design,2006
[12]	施法中. 计算机辅助几何设计与非均匀有理B样条[M].北京:高等教育出版社,2001
[13]	任军学,张定华,王增强. 整体叶盘数控加工技术研究[J].航空学报,2004,25(2):205-208
[14]	单晨伟,任军学,张定华. 开式整体叶盘四坐标侧铣开槽粗加工轨迹规划[J].中国机械工程,2007,18(16):1917-1920
[15]	刘雄伟,张定华. 数控加工理论与编程技术[M].北京:机械工业出版社,2000.