基于Adams和AMESim的高线打包头联合仿真

基金项目:

福建省教育厅项目(JA10027)资助

Co-simultion of High Wire Baler-header Based on Adams and AMESim

1.
School of Mechanical Engineering and Automation, Fuzhou University, Fuzhou 350108

摘要: 采用Adams和AMESim分别建立打包头的机械系统和液压控制系统模型,并在AMESim中将两子系统模型根据参数关联有机集成为机电液一体化模型,最终实现打包头机械、液压和控制系统的联合仿真。联合仿真结果表明:打包头不同阶段的运动与设定目标一致,从而验证了打包头机械系统模型以及液压回路和参数设置的正确性。
- 打包头 /
- Adams /
- AMESim /
- 联合仿真
Abstract: To make the movements of high wire baler-header meet the operating requirements,the mechanical model and hydraulic system model of baler-header were built with Adams and AMESim in this paper,an electromechanical liquid integration model was integrated with two subsystem models according to the associated parameters in AMESim,and the co-simulation of the mechanical system,hydraulic system and control system was achieved.The co-simulation results showed that the movement of baler-header at different stages is consistent with the setting one,and the correctness of the mechanical model,hydraulic circuit and parameters were also verified.The present study provid a valid theoretic basis for the parameter design and manufacturing of baler-header prototype.
- baler-header /
- Adams /
- AMESim /
- Co-simultion

[1]	万占鸿. 打捆机驱动轮系统接触问题有限元分析及驱动轮磨损寿命估算[D]. 鞍山:鞍山科技大学，2003
[2]	钟国荣. 基于现场总线网络的打包机控制系统设计[D]. 武汉:华中科技大学，2006
[3]	夏云龙，张洁，陈洪波. 宣钢高线自动打包机应用实践[A].2008 年全国小型型钢生产技术交流会论文集[C]，2008:331～334
[4]	汪菲. 基于 AMESim 的顶驱用轴向柱塞泵仿真[J]. 机械科学与技术，2011，30(11):1816-1821
[5]	尹忠俊，赵益春，陈兵，韩天. 基于多体动力学的热轧卷取机踏步系统联合仿真[J]. 系统仿真学报，2008，20 (2):473－484
[6]	傅鹏飞. 基于 ADAMS 和 AMESim 混凝土泵车臂架仿真研究[D]. 镇江:江苏大学，2011
[7]	谢地，权龙. 基于 ADAMS 和 AMEsim 的装载机联合仿真[J].矿山机械，2011，39(10):27-32
[8]	Ma C L，et al. Modeling and simulation for electro-hydraulic sys-tems based on multi-sofyware collaboration[A]. Asia Simula-tion Conference-7th International Conference on SystemSimulation and Scientific Computing[C]，2008:110～114
[9]	付永领，祁晓野. LMS Imagine. Lab AMESim 系统建模和仿真参考手册[M]. 北京:北京航空航天大学出版社，2011
[10]	Wan L R，Wu X W，Wang C L，et al. Mechanical-hydraulic in-tegration modeling and simulation of hydraulic support[A]. In-ternational Conference on Computer Application and SystemModeling[C]，2010:69～72