|
|
论文:2024,Vol:42,Issue(3):540-549 |
|
|
引用本文： |
|
|
蔡威, 付晓军, 马尚君, 李欣, 刘更. 不同方向上行星滚柱丝杠螺纹副啮合侧隙研究[J]. 西北工业大学学报 |
|
|
CAI Wei, FU Xiaojun, MA Shangjun, LI Xin, LIU Geng. Studies on meshing clearance of thread pairs of planetary roller screw mechanism in different directions[J]. Journal of Northwestern Polytechnical University |
|
|
|
|
|
|
|
| 不同方向上行星滚柱丝杠螺纹副啮合侧隙研究 |
|
| 蔡威, 付晓军, 马尚君, 李欣, 刘更 |
|
| 西北工业大学 陕西省机电传动与控制工程实验室, 陕西 西安 710072 |
| 摘要: |
| 根据丝杠、滚柱以及螺母结构特征,利用空间曲面参数方程分别建立了行星滚柱丝杠各个零件的螺旋曲面模型,并结合行星滚柱丝杠装配关系,得到行星滚柱丝杠空间啮合曲面方程。在此基础上,获得螺旋曲面法向量,基于曲面啮合条件,考虑零件运动方向,建立了行星滚柱丝杠在轴向、径向以及周向上的啮合侧隙模型,并讨论了结构参数对行星滚柱丝杠啮合侧隙的影响规律。结果表明,滚柱与丝杠侧在3个方向上的啮合点均不在螺纹中径,滚柱与螺母侧3个方向上的啮合点均在滚柱螺纹中径位置;螺距、牙侧角以及螺纹牙厚均对行星滚柱丝杠啮合侧隙有影响,只有增大螺纹牙厚才能同时减小3个方向上的啮合侧隙,螺距和牙侧角应根据实际需要选择合适的参数。 |
| 关键词:
行星滚柱丝杠
螺纹副
曲面方程
不同方向
啮合侧隙
|
|
| Studies on meshing clearance of thread pairs of planetary roller screw mechanism in different directions |
|
| CAI Wei, FU Xiaojun, MA Shangjun, LI Xin, LIU Geng |
|
| Shaanxi Engineering Laboratory for Transmissions and Controls, Northwestern Polytechnical University, Xi'an 710072, China |
| Abstract: |
| The helix surface model of planetary roller screw mechanism (PRSM) is established by utilizing the parametric equations of space surface according to the structural features of screw, roller and nut. The helix surface model of PRSM is improved in consideration of the PRSM assembly relationship. The normal vector equations of helix surfaces are obtained based on the helix surface model. The meshing clearance models of PRSM in axial, radial and circumferential directions are built considering the movement direction of parts utilizing surface meshing conditions. The influence of structural parameters on the meshing clearance of PRSM is also analyzed. The results show that the meshing points between the roller and the screw in three directions are not in the middle diameter. The meshing points in the three directions of the roller and the nut are in the middle diameter of the roller. The pitch, tooth angle and tooth thickness of the thread all have an influence on the meshing clearance of PRSM. Only by increasing the tooth thickness of the thread can the meshing clearance in the three directions be reduced at the same time. The pitch and tooth angle should be selected properly to meet the practical requirements. |
| Key words:
planetary roller screw mechanism
thread pairs
different directions
meshing clearance
|
|
| 收稿日期: 2023-05-16
修回日期:
|
| DOI: 10.1051/jnwpu/20244230540 |
| 基金项目: 国家自然科学基金(51905428,51875458)资助 |
| 通讯作者: 刘更(1961—),教授 e-mail:npuliug@nwpu.edu.cn
Email：npuliug@nwpu.edu.cn |
| 作者简介: 蔡威(1994—),博士研究生
|
|
| 相关功能 |
|
|
|
|
| 作者相关文章 |
|
| 蔡威 在本刊中的所有文章 |
| 付晓军 在本刊中的所有文章 |
| 马尚君 在本刊中的所有文章 |
| 李欣 在本刊中的所有文章 |
| 刘更 在本刊中的所有文章 |
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] YAO Q, ZHANG M, LIU Y, et al. Multi-objective optimization of planetary roller screw mechanism based on improved mathematical modelling[J]. Tribology International, 2021, 161: 107095
[2] 乔冠, 刘更, 马尚君. 行星滚柱丝杠副主曲率计算与接触特性分析[J]. 机械工程学报, 2020, 56(21): 140-148 QIAO Guan, LIU Geng, MA Shangjun. Principal curvature calculation and contact characteristics analysis of the planetary roller screw mechanism[J]. Journal of Mechanical Engineering, 2020, 56(21): 140-148(in Chinese)
[3] MENG J J, DU X, LI Y M, et al. A multiscale accuracy degradation prediction method of planetary roller screw mechanism based on fractal theory considering thread surface roughness[J]. Fractal and Fractional, 2021, 5(4): 1-20
[4] GRUSZECKI J, GRZYBOWSKI J, RZUCIDLO P. Electro-mechanical actuators for general aviation fly-by-wire aircraft[J]. Aviation, 2005, 9: 19-25
[5] LIU Y Q, WANG J S, CHENG H X. Kinematics analysis of the roller screw based on the accuracy of meshing point calculation[J]. Mathematical Problems in Engineering, 2015, 2015: 303972
[6] ANDRADE A, NICOLOSI D, LUCCHI J, et al. Auxiliary total artificial heart: a compact electromechanical artificial heart working simultaneously with the natural heart[J]. Artificial Organs, 1999, 23: 876-880
[7] ZHOU G W, ZHANG Y H, WANG Z Z, et al. Analysis of transient mixed elastohydrodynamic lubrication in planetary roller screw mechanism[J]. Tribology International, 2021, 163: 107158
[8] ABEVI F, DAIDIE A, CHAUSSUMIER M, et al. Static load distribution and axial stiffness in a planetary roller screw mechanism[J]. Journal of Mechanical Design, 2016, 138: 012301
[9] DU X, CHEN B, ZHENG Z. Investigation on mechanical behavior of planetary roller screw mechanism with the effects of external loads and machining errors[J]. Tribology International, 2021, 154: 106689
[10] AUREGAN G, FRIDRICI V, KAPSA P, et al. Experimental simulation of rolling-sliding contact for application to planetary roller screw mechanism[J]. Wear, 2015, 332/333: 1176-1184
[11] LI L J, FU Y L, ZHENG S C, et al. Friction torque analysis of planetary roller screw mechanism in roller jamming[J]. Mathematical Problems in Engineering, 2020(12): 1392380
[12] QIAO G, LIU G, MA S J, et al. Thermal characteristics analysis and experimental study of the planetary roller screw mechanism[J]. Applied Thermal Engineering, 2019, 149: 1345-1358
[13] LI X, LIU G, FU X J, et al. Review on motion and load-bearing characteristics of the planetary roller screw mechanism[J]. Machines, 2022, 10(317): 1-15
[14] VELINSKY S A, CHU B, LASKY T A. Kinematics and efficiency analysis of the planetary roller screw mechanism[J]. Journal of Mechanical Design, 2009, 131: 011016
[15] CAI W, LIU G, MA S J, et al. A dynamic separable convolution RCNN for lubrication condition identification of planetary roller screw mechanism[J]. Advances in Mechanical Engineering, 2022, 14(4): 1-15
[16] 赵英, 倪洁, 吕丽娜. 滚柱丝杠副的啮合计算[J]. 机械设计, 2003, 20(3): 34-35 ZHAO Ying, NI Jie, LYU Lina, et al. Mesh calculation of roller screw pair[J]. Journal of Machine Design, 2003, 20(3): 34-35(in Chinese)
[17] JONES M H, VELINSKY S A. Contact kinematics in the roller screw mechanism[J]. Journal of Mechanical Design, 2013, 135: 051003
[18] 付晓军, 刘更, 马尚君, 等. 行星滚柱丝杠副螺旋曲面啮合机理研究[J]. 机械工程学报, 2016, 52(3): 26-33 FU Xiaojun, LIU Geng, MA Shangjun, et al. Studies on meshing mechanism of helical surfaces in planetary roller screw mechanism[J]. Journal of Mechanical Engineering, 2016, 52(3): 26-33(in Chinese)
[19] SANDU S, BIBOULET N, NELIAS D, et al. An efficient method for analyzing the roller screw thread geometry[J]. Mechanism and Machine Theory, 2018, 126: 243-264
[20] 陈士云, 范元勋, 雷建杰. 行星滚柱丝杠啮合计算与干涉消除[J]. 组合机床与自动化加工技术, 2018(8): 4-7 CHEN Shiyun, FAN Yuanxun, LEI Jianjie. Mesh calculation and interference elimination of the planetary roller screw[J]. Modular Machine Tool and Automatic Manufacturing Technique, 2018(8): 4-7(in Chinese)
[21] 刘靖楠, 范元勋. 考虑误差的行星滚柱丝杠副啮合模型研究[J]. 机械制造与自动化, 2021, 50(6): 143-147 LIU Jingnan,FAN Yuanxun. Study on load meshing model of planetary roller screw considering errors[J]. Mechine Building and Automation, 2021, 50(6): 143-147(in Chinese) |
|
|
|
|
|
|
|
