论文:2017,Vol:35,Issue(3):414-421
引用本文:
肖文耀, 贺尔铭, 胡亚琪. 基于改进遗传算法的连接件螺栓布局优化新方法[J]. 西北工业大学学报
Xiao Wenyao, He Erming, Hu Yaqi. A New Method of Optimizing Bolts Layout in Connector Based on Improved Genetic Algorithm[J]. Northwestern polytechnical university

基于改进遗传算法的连接件螺栓布局优化新方法
肖文耀, 贺尔铭, 胡亚琪
西北工业大学 航空学院, 陕西 西安 710072
摘要:
航空结构承力连接件的螺栓孔边及其毗邻区域常会出现应力集中现象,研究连接件上的螺栓布局对飞机结构安全性有着重要的工程意义。为了优化孔边应力,建立了典型螺栓连接结构的有限元参数化模型;针对传统遗传算法(TGA) 在工程应用上的局限性,结合单亲遗传算法(PGA)与混沌遗传算法(CGA)的优势,提出了新的单亲混沌遗传算法(PCGA);运用该算法并采用非均匀螺栓排布方案对连接件螺栓布局进行了优化,与原有螺栓布局设计方案相比,在30 MPa的静压工况载荷下可使孔边等效应力下降31.03%,再经过螺栓数量优化还可使螺栓数量减少近50%;最后,将该方法用于某型飞机机翼内外翼连接区域的螺栓布局优化,在最严重工况下可使7#肋与蒙皮连接处的最大等效应力下降了23.36%,且螺栓数减少10%。此方法为航空连接件螺栓布局设计提供了一种新思路。
关键词:    螺栓    布局优化    遗传算法    参数化    有限元分析   
A New Method of Optimizing Bolts Layout in Connector Based on Improved Genetic Algorithm
Xiao Wenyao, He Erming, Hu Yaqi
School of Aeronautics, Northwestern Polytechnical University, Xi'an 710072, China
Abstract:
The phenomenon of stress concentration often appears at the edge of the bolts hole and its adjacent areas in aviation engineering field. Therefore, the study on bolts layout of connection structure has important engineering meaning. In order to optimize stress at the hole edge, this paper establishes a parameterized model of bolts connection structure based on the finite element method (FEM). In view of the limitation of the traditional genetic algorithm (TGA) in engineering application, a new partheno-chaos genetic algorithm (PCGA) is proposed by combining partheno genetic algorithm (PGA) and chaos genetic algorithm (CGA). The new algorithm is applied to optimize bolts layout design and a new method of non-uniformity is adopted. Compared with the original bolts layout design, the maximum hole edge stress is decreased by 31.03% under the condition of a surface pressure load of 30 Mpa; and the number of bolts can also be reduced approximately by 50% by the bolts quantity optimization. Last the method is applied to the bolt layout of the inner and outer wings of a certain aircraft. After the optimization, the number of bolts is decreased by 10% and the maximum equivalent stress of 7# rib and skin is decreased by 23.36% under the severe conditions. This method provides a new idea for bolts layout design in the connection area of aircraft structure.
Key words:    bolts    layout optimization    genetic algorithms    parameterization    finite element analysis   
收稿日期: 2017-03-01     修回日期:
DOI:
基金项目: 国家自然科学基金(51675426)资助
通讯作者:     Email:
作者简介: 肖文耀(1990-),西北工业大学硕士研究生,主要从事计算固体力学研究。
相关功能
PDF(2128KB) Free
打印本文
把本文推荐给朋友
作者相关文章
肖文耀  在本刊中的所有文章
贺尔铭  在本刊中的所有文章
胡亚琪  在本刊中的所有文章

参考文献:
[1] Kim J, Yoon J C, Kang B S. Finite Element Analysis and Modeling of Structure with Bolted Joints[J]. Applied Mathematical Modelling, 2007, 31(5):895-911
[2] 张岐良, 曹增强. 复合材料螺接性能的影响因素研究[J]. 航空学报, 2012, 33(4):755-762 Zhang Qiliang, Cao Zengqiang. Study on Factors Influencing the Performance of Composite Bolted Connections[J]. Acta Aeronautica et Astronautica Sinica, 2012, 33(4):755-762(in Chinese)
[3] Pedersen N L. Overall Bolt Stress Optimization[J]. Journal of Strain Analysis for Engineering Design, 2013, 48(3):155-165
[4] Xia T, Yao W, Xu L, et al. Metamodel-Based Optimization of the Bolted Connection of a Wing Spar Considering Fatigue Resistance[J]. Aerospace Engineering, 2015, 230(5):805-814
[5] Kradinov V, Madenci E, Ambur D R. Application of Genetic Algorithm for Optimum Design of Bolted Composite Lap Joints[J]. Composite Structures, 2007, 77(2):148-159
[6] 罗群,樊新田,李宁. 机身壁板有头铆钉自动钻铆干涉量研究[J]. 航空精密制造技术, 2016, 52(3):21-24 Luo Qun, Fan Xintian, Li Ning. Interference Research on Aircraft Fuselage Panel Automatic Drilling and Riveting of Head Rivet[J]. Aviation Precision Manufacturing Technology, 2016, 52(3):21-24(in Chinese)
[7] 王国夫,王鹢,孙尧,等. 混合GA与SA求解非线性约束优化[J]. 哈尔滨工程大学学报, 2002, 23(6):73-76 Wang Guofu, Wang Yi, Sun Yao, et al. Hybrid GA and SA for Solving Nonlinear Constrained Optimization Problems[J]. Journal of Harbin Engineering University, 2002(6):73-76(in Chinese)
[8] Mu S, Su H, Mao W, et al. A New Genetic Algorithm to Handle the Constrained Optimization Problem[C]//Proceedings of the IEEE Conference on Decision and Control, 2003:739-740
[9] Deb K. An Efficient Constraint Handling Method for Genetic Algorithms[J]. Computer Methods in Applied Mechanics & Engineering, 2000, 186(2/3/4):311-338
[10] 《飞机设计手册》总编委会. 2、9、10册[S]. 北京:航空工业出版社, 2000 Aircraft Design Manual. Editorial Board. 2、9、10 Volumes[S]. Beijing, Aviation Industry Press, 2000
[11] 高尚德. 螺栓连接结构的参数化有限元分析与优化设计[D]. 西安:西北工业大学, 2013:13 Gao Shangde. Parametric Finite Element Analysis and Optimization Design of Bolt Connection Structure[D]. Xi'an, Northwestern Polytechnical University, 2013:13(in Chinese)
[12] 杨海波. 飞机连接接头的细节应力分析与优化设计研究[D]. 西安:西北工业大学, 2007:43-46 Yang Haibo. Study on the Stress Analysis and Optimum Design of Aircraft Connection Joint[D]. Xi'an, Northwestern Polytechnical University,2007:43-46(in Chinese)
[13] 王增山, 虞伟建, 王开福. 基于ANSYS的机翼接头强度分析及优化设计[J]. 机械设计与制造, 2009(7):47-49 Wang Zengshan, Yu Weijian, Wang Kaifu. Strength Analysis and Optimization Design for Wing Joint Based on ANSYS[J]. Machinery Design & Manufacture, 2009(7):47-49(in Chinese)
[14] 郁大照, 陈跃良, 高永. 螺栓连接单搭接件疲劳特性试验与全寿命估算方法研究[J]. 中国机械工程, 2013, 24(20):2747-2752 Yu Dazhao, Chen Yueliang, Gao Yong. Study on Fatigue Property Tests and Holistic Life Assessment Method for Single Bolted Joints[J]. china Mechanical Engineering, 2013, 24(20):2747-2752(in Chinese)
[15] 李茂军, 罗日成, 童调生. 单亲遗传算法的遗传算子分析[J]. 系统工程与电子技术, 2001, 23(8):84-87 Li Maojun, Luo Richeng, Tong Tiaosheng. Analysis on the Genetic Operators of Partheno-Genetic Algorithm[J]. Systems Engineering & Electronics, 2001, 23(8):84-87(in Chinese)
[16] 梁俊毅,张建龙,马雪瑞,等. 基于多混沌算子遗传算法的混合动力汽车控制策略优化[J]. 上海交通大学学报, 2015, 49(4):442-449 Liang Junyi, Zhang Jianlong, Ma Xuerui, et al. Control Strategy Optimization for Hybrid Electric Vehicle Based on Multi-Chaotic Operators Genetic Algorithm[J]. Journal of Shanghai Jiaotong University, 2015, 49(4):442-449(in Chinese)
[17] Ren B, Zhong W. Multi-Objective Optimization using Chaos Based PSO[J]. Information Technology Journal, 2011, 10(10):1908-1916