BFPC数控车床斜床身拓扑优化设计及其性能分析

于英华; 孙苗苗; 徐平; 吴荣发

doi:10.13433/j.cnki.1003-8728.2018.0706

BFPC数控车床斜床身拓扑优化设计及其性能分析

doi: 10.13433/j.cnki.1003-8728.2018.0706

1.
辽宁工程技术大学机械工程学院, 辽宁阜新 123000

基金项目:

国家自然科学基金项目（51375219）资助

详细信息

作者简介:
于英华(1965-),教授,博士生导师,博士,研究方向为机械系统动力学分析与控制、先进制造技术与系统等,xuvicky199128@163.com

计量
- 文章访问数: 232
- HTML全文浏览量: 32
- PDF下载量: 15
- 被引次数: 0
出版历程
- 收稿日期: 2017-07-11
- 刊出日期: 2018-07-05

Topological Optimization Design and Performance Analysis of BFPC Oblique bed CNC Lathe

1.
School of Mechanical Engineering, Liaoning Technical University, Liaoning Fuxin 123000, China

摘要

摘要: 为提高机床基础件静、动态性能和轻质性，以某数控车床斜床身为原型，初步设计玄武岩纤维树脂混凝土（Basalt fiber polymer concrete，BFPC）斜床身，分析典型工况下该床身的受力情况，并对两种床身的静态、动态特性和质量进行仿真分析和计算；对BFPC床身进行拓扑优化设计，根据拓扑优化设计结果和BFPC床身的制造工艺性，重构BFPC床身结构，以其减重孔尺寸参数为因素，以其前六阶模态的固有频率和质量为试验指标，进行单因素轮换试验研究，最终确定其数值；对优化后的BFPC床身的静、动态性能和轻质性进行仿真分析和计算，再与原型和优化前的BFPC床身的相应性能进行对比分析。结果表明，拓扑优化设计后的BFPC床身在静、动态性能和轻质性方面都明显优于后两种床身。
- 玄武岩纤维树脂混凝土 /
- 车床 /
- 优化 /
- 静动态特性 /
- 轻质性
Abstract: To improve the static and dynamic performance and lightness of a machine tool. This paper take a CNC lathe's oblique bed as the prototype preliminary design of a basalt fiber polymer concrete (BFPC) oblique bed and analyze the force of the oblique bed under typical working conditions. The static and dynamic characteristics of the two kinds of oblique bed are simulated and analyzed. Then, the optimization design of the BFPC oblique bed is carried out according to the topological optimization results and manufacturing processes of the BFPC oblique bed, whose structure is reconstructed. With the factor of its weight reduction pore size taken into consideration, the natural frequency of the first six modes are used as experimental indexes. Finally, experiments on single-factor rotation is conducted to determine the numerical value. The static and dynamic performance and lightness of the optimized BFPC bed are simulated and calculated and then compared with the prototype and optimized BFPC oblique beds before their corresponding performance is analyzed. The results show that the topologically optimized BFPC oblique bed is obviously better than the latter two in terms of static and dynamic performance and lightness.
- basalt fiber resin concrete /
- lathes /
- optimization /
- static and dynamic characteristics /
- lightness

HTML全文

参考文献(15)

[1]	王涛.机床用碳纤维增强树脂矿物复合材料的制备与性能研究[D].济南:山东大学,2014 Wang T. Preparation and property study of carbon fiber reinforced resin mineral composite for machine tool[D]. Ji'nan:Shandong University, 2014(in Chinese)
[2]	Möhring H C, Brecher C, Abele E, et al. Materials in machine tool structures[J]. CIRP Annals, 2015,64(2):725-748
[3]	Aggogeri F, Merlo A, Mazzola M. Multifunctional structure solutions for Ultra High Precision (UHP) machine tools[J]. International Journal of Machine Tools and Manufacture, 2010,50(4):366-373
[4]	Cho S K, Kim H J, Chang S H. The application of polymer composites to the table-top machine tool components for higher stiffness and reduced weight[J]. Composite Structures, 2011,93(2):492-501
[5]	徐平,沈佳兴,于英华,等.玄武岩纤维树脂混凝土阻尼特性研究[J].非金属矿,2017,40(1):30-32 Xu P, Shen J X, Yu Y H, et al. Study on damping properties of basalt fiber reinforced polymer concrete[J]. Non-Metallic Mines, 2017,40(1):30-32(in Chinese)
[6]	徐平,沈佳兴,于英华,等.偶联时间对玄武岩纤维树脂混凝土强度的影响[J].非金属矿,2016,39(3):47-49,80 Xu P, Shen J X, Yu Y H, et al. Inlfuence of coupling time on strength of basalt fiber reinforced polymer concrete[J]. Non-Metallic Mines, 2016,39(3):47-49,80(in Chinese)
[7]	于英华,梁宇,沈佳兴,等.玄武岩纤维增强树脂混凝土机床基础件结构设计及其性能仿真分析[J].机械设计,2017,34(1):71-75 Yu Y H, Liang Y, Shen J X, et al. Structure design and performance simulation of a machine tool components made of BFPC[J]. Journal of Machine Design, 2017,34(1):71-75(in Chinese)
[8]	陈叶林,丁晓红,郭春星,等.机床床身结构优化设计方法[J].机械设计,2010,27(8):65-68 Chen Y L, Ding X H, Guo C X, et al. Study on optimizing design method of machine tool bed structure[J]. Journal of Machine Design, 2010,27(8):65-68(in Chinese)
[9]	蒋大伟,芮执元.控制臂多目标拓扑优化研究[J].机械强度,2014,36(3):408-412 Jiang D W, Rui Z Y. Research on multi-objective topology optimization for control arm[J]. Journal of Mechanical Strength, 2014,36(3):408-412(in Chinese)
[10]	罗辉,陈蔚芳,叶文华.机床立柱灵敏度分析及多目标优化设计[J].机械科学与技术,2009,28(4):487-491 Luo H, Chen W F, Ye W H. Sensitivity analysis and multi-objective optimization design of a machine column[J]. Mechanical Science and Technology, 2009,28(4):487-491(in Chinese)
[11]	Chen T Y, Wu S C. Multiobjective optimal topology design of structures[J]. Computational Mechanics, 1998,21(16):483-492
[12]	陈静,杨泽龙,张政泼.基于有限元的加工中心立柱多目标拓扑优化[J].机械科学与技术,2014,33(7):982-986 Chen J, Yang Z L, Zhang Z P. Multi-objective topology optimization of machining center column based on the finite element method[J]. Mechanical Science and Technology for Aerospace Engineering, 2014,33(7):982-986(in Chinese)
[13]	郭垒,张辉,叶佩青,等.基于灵敏度分析的机床轻量化设计[J].清华大学学报(自然科学版),2011,51(6):846-850 Guo L, Zhang H, Ye P Q, et al. Light weight design of a machine tool based on sensitivity analysis[J]. Journal of Tsinghua University (Science & Technology), 2011,51(6):846-850(in Chinese)
[14]	雷磊,王玺.解决模糊多目标线性规划问题的折衷模型研究[J].统计与决策,2015,30(18):15-18 Lei L, Wang X. Study on a compromise model for fuzzy multiobjective linear programming[J]. Statistics and Decision, 2015,30(18):15-18(in Chinese)
[15]	郭瑞,张建方.单因素轮换试验的一个调查研究[J].数理统计与管理,2008,27(3):432-438 Guo R, Zhang J F. A research on one-factor-at-a-time experimentation[J]. Application of Statistics and Management, 2008,27(3):432-438(in Chinese)