间隙补偿及液体垫片参数对层合板单层与层间应力的影响

蒋麒麟; 安鲁陵; 云一珅; 高国强; 肖睿恒

doi:10.13433/j.cnki.1003-8728.2017.1024

间隙补偿及液体垫片参数对层合板单层与层间应力的影响

doi: 10.13433/j.cnki.1003-8728.2017.1024

1.
南京航空航天大学机电学院, 南京 210016;
2.
南京工程学院机械学院, 南京 211167;
3.
上海飞机制造有限公司航空制造技术研究所, 上海 200436

基金项目:

国家商用飞机制造工程技术研究中心创新基金（SAMC13-JS-15-021）、上海飞机制造有限公司委托关键技术攻关项目（JS-20130913/005）及南京工程学院机械工程学院重点学科开放课题（JXKJ201501）资助

详细信息

作者简介:
蒋麒麟(1976-),讲师,博士研究生,研究方向为飞机复合材料构件装配,jiangqilin@njit.edu.cn

计量
- 文章访问数: 222
- HTML全文浏览量: 26
- PDF下载量: 7
- 被引次数: 0
出版历程
- 收稿日期: 2016-06-08
- 刊出日期: 2017-10-05

Effect of Gap Compensation and Parameters of Liquid Shim on Composite Laminates Internal Stress and Interlaminar Stress

1.
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics & Astronautics, Nanjing 210016, China;
2.
School of Mechanical Engineering, Nanjing Institute of Technology, Nanjing 211167, China;
3.
Institute of Aeronautical Technology, Shanghai Aircraft Manufacturing Co., Ltd., Shanghai 200436, China

摘要

摘要: 在飞机装配中，一般采用液体垫片对复合材料层合板构件之间较小的装配间隙进行补偿。以复合材料层合板机械连接中典型的单螺栓连接为对象，考虑强迫装配（未实施间隙补偿）与采用液体垫片实施间隙补偿两种情况，设计了层合板应变测量实验；其次，利用ABAQUS建立有限元模型并进行计算验证，有限元模型计算结果与实验测量数据的吻合度较好。根据建立的模型，研究了间隙补偿及不同液体垫片参数下，层合板的单层面内应力与层间应力的变化。有限元分析结果表明：相对于强迫装配，随着间隙的增大，液体垫片对于改善层合板的应力分布、减小应力幅值、增强抗分层能力的作用愈加显著；三代液体垫片对层合板各单层面内应力与层间应力的影响差异非常微小；大幅增加垫片弹性模量后，单层面内应力的影响效果将明显提升。
- 复合材料层合板 /
- 机械连接 /
- 液体垫片 /
- 间隙补偿 /
- 应力
Abstract: In general, the liquid shim is used to compensate the small gaps between the composite components in the aircraft assembly. The single bolt connection of composite laminates as the object, one experiment were designed:the measurement of the strain of laminated plate, and two cases are considered in the process:using a liquid shim to compensate for the gap and without it; The finite element model was built and validated by using ABAQUS software. The calculation results are in a good agreement with the experimental. Under different liquid shim compensation parameters, the change in the stress of laminated plate, including laminates internal stress and interlaminar stress are studied based on the present model. The results show that:with the increasing of gap, the liquid shim is more significant to improve the stress distribution, reduce the stress amplitude, and enhance the ability to resist delamination; the three generations liquid shim have very little differences on laminates internal stress and interlaminar stress; laminates internal stress will be significantly improved if a substantial increase in the elastic modulus of the shim.
- composite laminates /
- mechanical connection /
- liquid shim /
- gap compensation /
- stress

HTML全文

参考文献(14)

[1]	王花娟,杨杰,刘新东,等.复合材料机械连接强度影响因素的研究进展[J].材料导报,2007,21(S3):438-440 Wang H J, Yang J, Liu X D, et al. Progress in research on affecting factors of mechanical joining strength of composite material[J]. Materials Review, 2007,21(S3):438-440(in Chinese)
[2]	张爽,王栋,郦正能,等.复合材料层合板机械连接结构累积损伤模型和挤压性能试验研究[J].复合材料学报,2006,23(2):163-168 Zhang S, Wang D, Li Z N, et al. Numerical calculation of damage accumulation and bearing strength experimental verification for composite single bolted joint[J]. Acta Materiae Compositae Sinica, 2006,23(2):163-168(in Chinese)
[3]	马毓,李飞,赵启林,等.复合材料构件机械连接接头破坏模式与机理[J].解放军理工大学学报(自然科学版),2010,11(6):658-663 Ma Y, Li F, Zhao Q L, et al. Failure mode and fracture mechanism of FRP constructional element mechanical connection joint[J]. Journal of PLA University of Science and Technology (Natural Science Edition), 2010,11(6):658-663(in Chinese)
[4]	崔海涛,温卫东.CFRP双剪单钉连接接头强度分析[J].宇航材料工艺,2004,(4):44-47 Cui H T, Wen W D. Strength analysis of single-bolted double-lapped joints in CFRP[J]. Aerospace Materials & Technology, 2004,(4):44-47(in Chinese)
[5]	黄春,李光丽,袁士平,等.机翼翼盒装配间隙精密补偿研究[J].航空制造技术,2010,(20):63-66 Huang C, Li G L, Yuan S P, et al. Research on active compensation for assembly gap of aircraft wing box[J]. Aeronautical Manufacturing Technology, 2010,(20):63-66(in Chinese)
[6]	Liu L. The influence of the substrate's stiffness on the liquid shim effect in composite-to-titanium hybrid bolted joints[J]. Journal of Aerospace Engineering, 2014,228(3):470-479
[7]	Dhôte J X, Comer A J, Stanley W F, et al. Study of the effect of liquid shim on single-lap joint using 3D digital image correlation[J]. Composite Structures, 2013,96:216-225
[8]	Hühne C, Zerbst A K, Kuhlmann G, et al. Progressive damage analysis of composite bolted joints with liquid shim layers using constant and continuous degradation models[J]. Composite Structures, 2010,92(2):189-200
[9]	Comer A J, Dhôte J X, Stanley W F, et al. Thermo-mechanical fatigue analysis of liquid shim in mechanically fastened hybrid joints for aerospace applications[J]. Composite Structures, 2012,94(7):2181-2187
[10]	Military materials handbook-MIL 17. Volume I:guidelines for characterization of structural materials[S]. 2002
[11]	ASTM D5961/D5961M-13 Standard test method for bearing response of polymer matrix composite laminates[S]. US:ASTM International, 2013
[12]	Qin T L, Zhao L B, Zhang J Y. Fastener effects on mechanical behaviors of double-lap composite joints[J]. Composite Structures, 2013,100:413-423
[13]	部标准编制组. 部标准《高锁螺栓、螺母》介绍[J].航空标准化,1981,(3):1-4 A Standard Drafting Group. High lock bolt and nut[J]. Standardization of Aviation, 1981,(3):1-4(in Chinese)
[14]	郭绍伟,张永存,宋恩鹏,等.开孔碳纤维层合板层间应力分析[J].复合材料学报,2011,28(5):228-233(in Chinese) Guo S W, Zhang Y C, Song E P, et al. Interlaminar stress analysis of carbon fiber-reinforced laminated plate with a hole[J]. Acta Materiae Compositae Sinica, 2011,28(5):228-233