复合材料螺栓干涉连接结构压钉过程轴向力建模

段元欣; 钟衡; 张开富; 程晖

doi:10.13433/j.cnki.1003-8728.2015.0831

复合材料螺栓干涉连接结构压钉过程轴向力建模

doi: 10.13433/j.cnki.1003-8728.2015.0831

1.
西北工业大学现代设计与集成制造教育部重点实验室, 西安 710072

基金项目:

国家自然科学基金项目（51175433）与航空科学基金项目（2014ZE53056）资助

详细信息

作者简介:
段元欣（1987-），博士研究生，研究方向为先进装配与连接技术，dmoxun@163.com

通讯作者:
张开富，教授，博士生导师，zhangkf@nwpu.edu.cn

计量
- 文章访问数: 118
- HTML全文浏览量: 29
- PDF下载量: 5
- 被引次数: 0
出版历程
- 收稿日期: 2014-01-02
- 刊出日期: 2015-08-05

An Analytical Model for Predicting Axial Force on Bolt Insertion Process of Composite Interference-fit Joint

1.
The Ministry of Education Key Laboratory of Contemporary Design and Integrated Manufacturing Technology, Northwestern Polytechnical University, Xi'an 710072, China

摘要

摘要: 复合材料干涉连接结构在螺栓压入过程中，由于螺栓杆与连接孔孔壁间存在显著的轴向相互作用，有可能在复材孔周引起分层损伤，更准确的控制轴向力对于提升复材干涉连接结构强度具有重要的意义。根据干涉配合螺栓压入过程中接触关系的变化，对压钉过程进行了阶段划分，并在经典层合板理论假设基础上，结合弹性力学复变函数方法，以干涉量为变量建立了螺接过程轴向力解析模型。基于ABAQUS软件，建立了干涉压入压钉过程的仿真模型，验证了解析模型的正确性。
- 干涉配合 /
- 螺栓连接 /
- 解析模型 /
- 有限元分析
Abstract: Axial force, which induced by the interference-fit on the close contact interface between bolt and hole, is the crucial element to dominate the delamination of composite plate during the bolt insertion process. A model for predicting the axial force on the bolt insertion process of composite interference-fit joint is presented. According to the variation in contact field between bolt and hole, the insertion process has been divided into different stages and the mechanical behaviors have been analyzed. Based on the classical laminated plate theory and elastic mechanics method of complex variable function, the model for axial force during installing had been established. A 3D FEA simulation of bolt inserting process with interference-fit is conducted to verify the present model. The good correlation is observed between the FEA and the model in various interference-fit.
- ABAQUS /
- bolted joints /
- boundary conditions /
- carbon fiber reinforced plastics

HTML全文

参考文献(10)

[1]	魏景超,矫桂琼,闫照明.单面螺纹抽钉干涉配合复合材料连接件挤压强度研究[J].航空学报,2013,34(7):1627-1635 Wei J C, Jiao G Q, Yan Z M. Bearing strength of composite joints interference fitted with blind bolts [J]. Acta Aeronautica et Astronautica Sinica,2013,34(7):1627-1635 (in Chinese)
[2]	Egan B, McCarthy C T, McCarthy M A, et al. Stress analysis of single-bolt, single-lap, countersunk composite joints with variable bolt-hole clearance[J]. Composite Structures, 2012,94(3):1038-1051
[3]	Thoppul S D, Finegan J, Gibson R F. Mechanics of mechanically fastened joints in polymer-matrix composite structures-a review[J]. Compos Sci Technol, 2009,69(3):301-329
[4]	Kim S Y, Hennigan D J. Influence of fabrication and interference-fit techniques on tensile and fatigue properties of pin-loaded glass fiber reinforced plastics composites[J]. J Eng Mater-T ASME, 2012,134(4):041012
[5]	Echavarría C, Haller P, Salenikovich A. Analytical study of a pin-loaded hole in elastic orthotropic plates[J]. Composite Structures, 2007, 79(1): 107-112
[6]	Aluko O, Whitworth H A, Owolabi G. Effect of friction on contact stress distribution in pin-loaded orthotropic plates[C]// International Mechanical Engineering Congress and Exposition. American Society of Mechanical Engineers, 2012:79-83
[7]	Olmedo A, Santiuste C, Barbero E. An analytical model for predicting the stiffness and strength of pinned-joint composite laminates[J]. Composites Science and Technology, 2014,90:67-73
[8]	中国航空科学技术研究院.飞机结构抗疲劳断裂强化工艺手册[M].北京:航空工业出版社,1993 China Institute of Aeronautical Science and Technology. Aircraft structural fatigue fracture hardening process manual[M]. Beijing: Aeration Industry Press, 1993 (in Chinese)
[9]	Lekhnitskii S G. Anisotropic plates[M]. Foreign Technology Div Wright-Patterson Afb Oh, 1968
[10]	罗祖道.各向异性材料力学[M].上海:上海交通大学出版社,1994 Luo Z D. Mechanics of anisotropic materials[M]. Shanghai: Shanghai Jiaotong University Press, 1994 (in Chinese)