一类利用摆线曲柄实现精确停歇的机构综合方法

周校民; 王忠; 郭瑞杰; 杨启坤

一类利用摆线曲柄实现精确停歇的机构综合方法

1.
中航工业成都凯天电子股份有限公司,成都 610091;
2.
西南科技大学,绵阳 621010;
3.
成都工具研究所有限公司,成都 610500

详细信息

作者简介:
周校民(1985-)，硕士研究生，研究方向为机构综合及机械设计，zhou2008515@126.com;王忠(联系人)，教授，博士，wangzhong@swust.edu.cn

周校民(1985-)，硕士研究生，研究方向为机构综合及机械设计，zhou2008515@126.com;王忠(联系人)，教授，博士，wangzhong@swust.edu.cn

计量
- 文章访问数: 138
- HTML全文浏览量: 11
- PDF下载量: 3
- 被引次数: 0
出版历程
- 收稿日期: 2011-08-14
- 刊出日期: 2015-06-10

The Design Method of Accurate-dwell Mechanism with Cycloid Crank

1.
AVIC Chengdu CAIC Electronics,Co.Ltd,Chengdu 610091;
2.
Southwest University of Science and Technology,Mianyang 621010;
3.
Chengdu Tool Research Institute,Chengdu 610500

摘要

摘要: 摆线曲柄机构的运动轨迹变化多样,可用于实现机构的停歇运动;但在设计过程中,实际摆线轨迹与理想轨迹存在一定的误差。为了减小摆线曲柄机构的轨迹误差,首先对这类机构的摆线参数方程、基本性质和运动特点进行了系统的分析,得到了摆线曲柄机构的运动规律;然后,根据行星轮和中心轮的啮合方式以及轨迹形状,分别对不同类型的摆线曲柄机构进行轨迹误差分析,并建立了相应的误差表达式;再按照误差极小的原则,使轨迹误差趋近于零,得到了误差最小条件下的机构参数设计要求;最后将其应用于4种典型结构的摆线曲柄精确停歇机构的设计,由此总结出摆线精确停歇机构的一般设计方法。
- 摆线 /
- 精确停歇 /
- 误差分析 /
- 机构综合
Abstract: The trajectory of cycloid crank is diverse,which could be applied to dwell mechanism.In the process of design,there are some error between the real cycloid trajectory and the ideal cycloid trajectory.In order to reduce the trajectory error of cycloid crank,a common kind of design method for the accurate-dwell mechanism was proposed in this paper.The character of cycloid movement equation was analyzed at first to obtain the movement rule of cycloid crank mechanism.Then,the orbital errors of different cycloid cranks were analyzed and these error expressions were set up.For reducing errors,the required design parameters of the mechanism were calculated based on the minimum error principle.Ultimately these parameters could be applied to design four kinds of dwell mechanism with cycloid crank.
- cycloid /
- accurate dwell /
- error analysis /
- mechanism design

HTML全文

参考文献(10)

[1]	韩继光,陆钟吕,吴荣羔. 带摆线曲柄的齿轮连杆机构综合[J].佳木斯工学院学报,1991,(03):129-133.
[2]	孔凡国,邹慧君,王行知. 摆线曲柄滑块摆杆间歇运动机构综合[J].机械传动,1996,(03):1-3.
[3]	Kota S. Generic models for designing dwell mechanisms:a novel kinematic design of stifling engines as an example[J].Journal of Mechanical,1991,(113).
[4]	Ümit Sönmez. Introduction to compliant long-dwell mechanism syn-thesis[A].Chicago,Illinois,USA,2003.
[5]	Koladiya D,Shiakolas P S,Kebrle J. ASME 2003 International Mechanical Engineering Congress and Exposition[M].Washing-ton,DC,USA,2003.
[6]	Beiner L. A three-gear linkage for generating dwell motions[J].Journal of Mechanical Design,Transactions of the ASME,2001,(04):637-640.
[7]	郑文纬,吴克坚. 机械原理[M].北京:高等教育出版社,1997.
[8]	张美麟. 机械创新设计[M].北京:化学工业出版社,2005.
[9]	黄纯颖,于晓红,唐进元. 机械创新设计[M].北京:高等教育出版社,2000.
[10]	常勇,刘远伟. 最佳传动角的平面曲柄滑块机构设计[J].机械科学与技术,1997,(04):633-635.