复合材料层合板界面裂纹能量释放率解析方法研究 -- 西北工业大学学报,2019,37(1):137-142
论文:2019,Vol:37,Issue(1):137-142
引用本文:
郑伟玲, 郑龙席. 复合材料层合板界面裂纹能量释放率解析方法研究[J]. 西北工业大学学报
ZHENG Weiling, ZHENG Longxi. Analytical Energy Release Rate of Interfacial Crack in Composite Laminates[J]. Northwestern polytechnical university

复合材料层合板界面裂纹能量释放率解析方法研究
郑伟玲, 郑龙席
西北工业大学 动力与能源学院, 陕西 西安 710072
摘要:
为了研究界面裂纹在复合材料中是否扩展,使用Timoshenko梁理论和局部广义力得到了三点弯曲模型中裂纹两端的解析能量释放率。研究结果和有限元结果进行对比验证,发现解析解和有限元结果相吻合。结果表明:裂纹在载荷点一侧时,左端和右端的能量释放率相等;当穿过载荷点以后,裂纹左端的能量释放率继续上升后逐渐下降,裂纹右端的能量释放率则下降后上升;当裂纹关于载荷点对称时,两端能量释放率相等。
关键词:    脱层    能量释放率    裂纹    梁理论    复合材料层合板   
Analytical Energy Release Rate of Interfacial Crack in Composite Laminates
ZHENG Weiling, ZHENG Longxi
School of Power and Energy, Northwestern Polytechnical University, Xi'an 710072, China
Abstract:
In order to study whether the interfacial crack will grow or not in the composite laminates, the energy release rate of a crack in three-point bending model was obtained by using the Timoshenko beam theory and local generalized forces. The results of energy release rate were validated by the finite element results. The results indicate that the energy release rate of left crack tip is equal to that of the right crack tip when the crack before the crack goes cross the loading point; after the crack goes cross the loading point, the energy release rate of the left crack tip increases and then decreases gradually, while the energy release rate of right crack tip decreases first and increases later; the energy release rate of left crack tip is equal to that of the right crack tip again when the crack is symmetric with the loading point.
Key words:    delamination    energy release rate    crack    beam theory    composites laminate   
收稿日期: 2018-01-22     修回日期:
DOI: 10.1051/jnwpu/20193710137
通讯作者:     Email:
作者简介: 郑伟玲(1983-),女,西北工业大学博士后,主要从事结构与计算力学研究。
相关功能
PDF(1364KB) Free
打印本文
把本文推荐给朋友
作者相关文章
郑伟玲  在本刊中的所有文章
郑龙席  在本刊中的所有文章

参考文献:
[1] MASSABO R, COX B. Concepts for Bridged Mode Ⅱ Delamination Cracks[J]. Journal of the Mechanics and Physics of Solids, 1999,47:1265-1300
[2] TURON A, COSTA J, CAMANHO P, et al. Simulation of Delamination in Composites under High-Cycle Fatigue[J]. Composites Part A:Applied Science and Manufacturing, 2007, 38(11):2270-2282
[3] KRUEGER R. The Virtual Crack Closure Technique:History, Approach and Application[R]. NASA CR-2002-211628
[4] KRAUSE T, TUSHTEV K, KOCH D, GRATHWOHL G. Interlaminar Mode I Crack Growth Energy Release Rate of Carbon/Carbon Composites[J]. Engineering Fracture Mechanics, 2013,100(100):38-51
[5] ZHENG W, KASSAPOGLOU C. Prediction of Delamination Onset and Growth for Apply Composite Laminates Using the Finite Element Method[J]. Composites Part A:Applied Science and Manufacturing, 2017,101:381-393
[6] SAPONARA V, MULIANA H, HAJ-ALI R, et al. Experimental and Numerical Analysis of Delamination Growth in Double Cantilever Laminated Beams[J]. Engineering Fracture Mechanics, 2002, 69:687-699
[7] CHEN I, PELEGRI A. Mixed Mode Testing of Fiber Reinforced Composites Using a Modified MMB Fixture[C]//41st Structures, Structaral Dynamics, and Materials Conference and Exhibit, 2000
[8] WILLIAMS J. On the Calculation of Energy Release Rate for Cracked Laminates[J]. International Journal of Fracture, 1988, 36(2):101-119
[9] SHEINMAN I, KARDOMATEAS G. Energy Release Rate and Stress Intensity Factors for Delaminated Composite Laminates[J]. International Journal of Solids and Structures, 1997,34(4):451-459
[10] OZDIL F, CARLSSON L. Beam analysis of Angle-Ply Laminate DCB Specimens[J]. Composites Science and Technology, 1999,59(2):305-315
[11] HAMED M, NOSIER A, FARRAHI G. Separation of Delamination Modes in Composite Beams with Symmetric Delaminations[J]. Materials & Design, 2006,27:900-910
[12] NAIRN J. On the calculation of Energy Release Rates for Cracked Laminates with Residual Stresses[J]. International Journal of Fracture, 2006,139:267-293
[13] ANDREWS M, MASSABO R, COX B. Elastic Interaction of Multiple Delaminations in Plates Subject to Cylindrical Bending[J]. International Journal of Solids and Structures, 2006,43(5):855-886
[14] SUN R, PANDEY R. Improved Method for Calculating Strain Energy Release Rate Based on Beam Theory[J]. AIAA Journal, 1994,32(1):184-189
[15] KASSAPOGLOU C. Design and Analysis of Composite Structures with Applications to Aerospace Structures[M]. UK:John Wiley & Sons, 2010