|
|
论文:2013,Vol:31,Issue(6):915-920 |
|
|
引用本文： |
|
|
郭辉, 赵宁, 侯圣文. 基于碟形砂轮的面齿轮磨齿加工误差分析及实验研究[J]. 西北工业大学 |
|
|
Guo Hui, Zhao Ning, Hou Shengwen. Tooth Deviation Analysis and Experimental Research of Face Gear Based on Disk Grinding Wheel[J]. Northwestern polytechnical university |
|
|
|
|
|
|
|
| 基于碟形砂轮的面齿轮磨齿加工误差分析及实验研究 |
|
| 郭辉, 赵宁, 侯圣文 |
|
| 西北工业大学 机电学院, 陕西 西安 710072 |
| 摘要: |
| 介绍了面齿轮分度展成磨齿加工原理及其实现方法。基于5坐标磨削机床,考虑机床安装误差等因素,建立了包含磨齿误差的面齿轮齿面方程。对面齿轮工作齿面的旋转投影面进行了网格规划,并给出齿面偏差的计算方法。通过仿真计算研究了机床与砂轮的安装误差对面齿轮齿面偏差的影响规律。最后在5坐标曲面磨床上进行了面齿轮磨齿加工实验,并根据齿轮测量中心获得的齿面误差数据对机床加工参数进行了矫正。重新磨齿并测量后发现面齿轮齿面误差明显降低,齿面精度得到明显提高。 |
| 关键词:
面齿轮
齿面偏差
参数矫正
磨齿加工
实验
误差分析
测量
碟形砂轮
|
|
| Tooth Deviation Analysis and Experimental Research of Face Gear Based on Disk Grinding Wheel |
|
| Guo Hui, Zhao Ning, Hou Shengwen |
|
| Department of Mechanical Engineering, Northwestern Polytechnical University, Xi'an 710072, China |
| Abstract: |
| The single indexing generating grinding method of a face gear is introduced.The face gear tooth surface equation with errors is established on the basis of five coordinate grinding machine tool and through considering fac -tors such as machine tool setting error.The measurement grid schema was accomplished on the rotary projection of face gear tooth surface;the tooth surface deviation could be calculated.The effect of errors of alignment on tooth surface deviation was investigated by simulation.Finally, a grinding processing experiment is done on a grinding machine with five coordinates.The processing parameters are corrected according to the measurement results of tooth surface errors at a gear measurement center.The tooth surface error is decreased obviously after grinding again and the precision of face gear tooth surface is improved obviously. |
| Key words:
error analysis
error correction
experiments
gears
machining
grinding wheels
installation
measurements
process planning
face gear
installation errors
tooth surface deviation
|
|
| 收稿日期: 2013-03-18
修回日期:
|
| DOI: |
| 基金项目: 国家自然科学基金(50675176、51075328、51105307)资助 |
| 通讯作者:
Email： |
| 作者简介: 郭辉(1978-),西北工业大学教师、博士,主要从事机械动力学及齿轮几何等的研究。
|
|
| 相关功能 |
|
|
|
|
| 作者相关文章 |
|
| 郭辉 在本刊中的所有文章 |
| 赵宁 在本刊中的所有文章 |
| 侯圣文 在本刊中的所有文章 |
|
|
|
|
|
|
|
|
参考文献: |
|
|
[1] 王志, 石照耀. 面齿轮传动的特点及研究进展. 工具技术, 2009, 43(10): 10-14 Wang Zhi, Shi Zhaoyao. Characteristics of Face Gear Drive and Its Research Developments. Tool Engineering, 2009, 43(10):10-14 (in Chinese)
[2] Filler R R, Heath G F, Slaughter S C, et al. Torque Splitting by a Concentric Face Gear Transmission. The American Helicopter Society 58th Annual Forum, Montreal, Canada, 2002, 11-22
[3] 李政民卿, 朱如鹏. 基于包络法的正交面齿轮齿廓尖化研究. 中国机械工程, 2008, 19(9): 1029-1033 Li Zhengminqing, Zhu Rupeng. Research on Pointing of Face Gear by Enveloping Method. China Mechanical Engineering,2008, 19(9): 1029-1033 (in Chinese)
[4] Stadtfeld H J. CONIFACE Face Gear Cutting and Grinding. GEAR Solutions, 2010(9): 38-47
[5] 苏进展, 方宗德, 谷建功. 螺旋锥齿轮齿面误差修正. 农业机械学报, 2010, 41(3): 201-203 Su Jinzhan, Fang Zongde, Gu Jiangong. Tooth Surface Correction for Spiral Bevel Gears. Transactions of the Chinese Society of Agricultural Machinery, 2010, 41(3): 201-203 (in Chinese)
[6] Shih Y P, Fong Z H. Flank Modification Methodology for Face-Hobbing Hypoid Gears Based on Ease-Off Topography. ASME J Mech Des, 2007, 129: 1294-1302
[7] Lin C Y, Tsay C B, Fong Z H. Computer-Aided Manufacturing of Spiral Bevel and Hypoid Gears with Minimum Surface Deviation. Mech Mach Theory, 1998, 33: 785-803
[8] 李敬财, 王太勇, 范胜波, 等. 基于数字化制造的螺旋锥齿轮齿面误差修正. 农业机械学报, 2008, 39(5): 174-177 Li Jingcai, Wang Taiyong, Fan Shengbo, et al. Error Corrections of Spiral Bevel Gear Tooth Surface Based on Digitized Manufacturing. Transactions of the Chinese Society of Agricultural Machinery, 2008, 39(5): 174-177 (in Chinese)
[9] 王志永, 曾韬. 弧齿锥齿轮基于比例修正参数的齿形误差修正. 机械工程学报, 2010, 46(1): 43-47 Wang Zhiyong, Zeng Tao. Correction of Tooth Flank Errors of Spiral Bevel Gear Based on Proportional Change Parameters. Journal of Mechanical Engineering, 2010, 46(1): 43-47 (in Chinese)
[10] 王小椿, 王军, 姜虹, 等. 螺旋锥齿轮的齿面测量及机床加工参数修正. 机械工程学报, 2003, 39(8): 25-28 Wang Xiaochun, Wang Jun, Jiang Hong, et al. Tooth Surface Mesurement and Machine-Settings Correction of Spiral Bevel Gear. Journal of Mechanical Engineering, 2003, 39(8): 125-128 (in Chinese)
[11] 郭辉. 面齿轮滚齿加工方法及其啮合性能研究: [博士学位论文]. 西安: 西北工业大学, 2009 Guo Hui. Research on M ethod of Hobbing Face -Gear and Gearing P erformance. P h. D. Thesis, Xi' an: Northwestern Polytechnical University, 2009 (in Chinese)
[12] 王军, 王小椿, 姜虹, 等. 螺旋锥齿轮齿面的三坐标测量. 机械工程学报, 2003, 39(6): 151-154 Wang Jun, Wang Xiaochun, Jiang Hong, et al. Coordinate M Easurement of Tooth Surface of Spiral Bevel Gear. Journal of Mechanical Engineering, 2003, 39(6): 151-154 (in Chinese) |
|
|
|
|
|
|
|
